Please see our COVID-19 Statement
MXR Phase 90 Script Pedal Mod

MXR Phase 90 Script Pedal Mod

MXR Phase 90 Script Pedal Mod

Item # 2217
In stock, ready to ship!

$9.63
$8.67

+
 
Total:
Qty:
Scroll to Top

MXR Phase 90 Script Pedal Mod

About This Item

Get two sounds from your MXR Phase 90
Switch between the classic MXR "script" and modern "block" sounds instantly

The MXR Phase 90 has a magical swirling sound that adds a subtle depth to your tone. The vintage "script" logo models had a much warmer and more organic tone than the later "block" logo versions. With just a few solder joints, you can experience both effects.

You don't need a new pedal! Mod your Phase 90 to sound how YOU want. It's easier than you think to get both sounds of your Phase 90. When you install the mod, you'll have a switch to change between modes to pick the right setting for you. It's like getting a vintage pedal for free!

It's more than just a schematic
We include step-by-step instructions for this mod with detailed pictures. Each step is fully illustrated in color with close-up views of every solder joint, component placement, and lug location.

And we even include directions on how to solder! If you get stuck give our techs a call—we'll walk you through it.

Start making and modding pedals
We've picked all of the right components to give you the best sound quality and reliability you need when tweaking your pedals. Take your first step into modding (and making) pedals and start customizing your sound.

MXR® is a registered trademark of Dunlop Manufacturing Inc.



CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


Instructions

Product Instructions

StewMac Pedal Mod Kit Instructions

Make all your pedals sound and play great.

Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
4.5
  • 4.50 average rating from 6 reviews
Sort by
4.0

Wiring overkill

By

Verified Buyer


+1 to the wiring overkill. The pushback wire is too stiff to be able to position the switch. Especially when you add the heat shrink, Also, the directions show the wire soldered straight up relative to the switch. It might be better solder the wires from the side to give more room.

4.0

Nice kit, easy and effective.

By

Verified Buyer


4 stars only for a few nit picks, otherwise very much worth the effort. Subtle warmer tone in script mode, preferred IMHO. Tips and nit picks. Toss the extra nut for the switch and just use the star washer between the switch and box. If you don't, the PCB presses against the switch body and really needs pressure applied, to the point of bending, to get the side jack nuts back in. The push back wire is a nice add but overkill for the application and very stiff. You solder the wire to one leg of a delicate resistor that you first desolder from the PCB, the stiff wire puts a lot of stress on the other leg that is still soldered to the board. Thinner PVC coated wire, like used in the battery pigtail would have been a better choice and would have made twisting and bending everything to get the PCB back in a lot easier.

5.0

Easy retro fit

By

Verified Buyer


Easy retro fit to enhance your MXR Phase 90 to produce broader spectrum of sounds.

4.0

Prefer Pre-Mod Sound

By

Verified Buyer


The kit was a fun project. Instructions were very good and the job was easy, if you have a little soldering experience. I was expecting a little more effect; in "script" mode the phasing is much more subtle. Suppose that could be preferable...

5.0

Best of Both Worlds with One Pedal

By

Verified Buyer


This mod actually does work as it says. Get both the SCRIPT and the BLOCK sound with one pedal. This mod gives me added sound options without adding another expensive pedal to the mix.
Thanks Stew Mac.

5.0

Nice mod for the MXR phase 90 pedal

By

Verified Buyer


This mod has easy to follow instructions and creates a warmer sounding phase when switch is engaged . I will definitely use this mod switched on in many of our bands songs .