Please see our COVID-19 Statement
Conductive Shielding Paint

Conductive Shielding Paint

StewMAX Member Appreciation Event
10% OFF + FREE SHIPPING*

Limited Time Offer
Add 1-year StewMAX Membership to my cart for $39.95
Conductive Shielding Paint 1/2 pint (236.6ml)

1/2 pint (236.6ml)

Item # 0029
In stock, ready to ship!

$41.49

+
Conductive Shielding Paint 1 pint (473.2ml)

1 pint (473.2ml)

Item # 0027
In stock, ready to ship!

$76.56

+
 
Total:
Qty:
Scroll to Top

Conductive Shielding Paint

About This Item

Reduces hum, noise and radio interference.
The fastest and easiest way to shield pickup and control cavities. Perfect for tight spots.

When connected to electrical ground, the shielded surfaces help reduce noise, hum and radio interference. It cleans up with water while still wet, and dries overnight.

Brush on two or more coats of this waterbase dark gray conductive paint for best results (let dry between coats). Conductive shielding paint is supplied in a 1/2-pint can, sufficient for shielding several electric guitars, and in a money-saving 1-pint can. We recommend our conductive tape for best results when shielding smooth plastic pickguards.


CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


Video

Instructions

Product Instructions

Conductive Shielding Paint Instructions

Directions for using conductive shielding paint.

Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
5.0
  • 4.78 average rating from 111 reviews
Sort by
5.0

Great Results!

By

Verified Buyer


Used a light layer a day for four days with 20-24 hours between each coat. Added a fan in the room and let it run a few hours after each coating. The results are very relieving. My squire and bullet are pure and free of hum or buzz. I should have never waited 12 years to re do the light work that was the original job inside. This products is loaded with bits and runs of the conductive recipe you need. I would recommend this product highly and especially from this distributor. My results are 5 star sounds and I got plenty left over with the full pint. Tremendous! Thank You StewMac. 1st Purchase here ever and it was the best!

5.0

Works like a charm

By

Verified Buyer


Works great!

5.0

Not a Peep

By

Verified Buyer


No buzzing or humming..follow the Stew Mac directions and this stuff works incredibly

5.0

Awesome product. Easy to use.

By

Verified Buyer


I got this to shield a Squier Telecaster that I bought a while back. It’s part of a complete redo - new Fender pups and Golden Age wiring kit. I used this product several years ago to shield a Squier Stratocaster. I think it may now be the quietest Strat on earth. Very easy to use. Applies like any paint and cleans up with water. Highly recommended.

5.0

Great RF shielding paint

By

Verified Buyer


I bought this and so glad I did to clear up the bass hum and the sound man hearing the radio in the background when my fingers were not on the strings. Very easy to apply and water clean up.

5.0

Conductive Shielding Paint

By

Verified Buyer


Great stuff, much easier to use than copper shielding and works as well

5.0

Works great!!!

By

Verified Buyer


Make sure you stir it good.

4.0

Took more than three coats, but my single coils guitars are quiet as a mouse

By

Verified Buyer


I got the small can and did both my Tele(parts)caster and Stratocaster. Painting through pick-up wire holes in the Tele body was a pain with pipe cleaners, but it eventually took. Strat was easier as it was more open. Each guitar took 4 coats and I probably have enough in the (small) can to do one more guitar (and I plan on building another tele at some point). I feel the paint will hold up better in the long run than copper tape. I would buy it again if the project called for it.

5.0

Conductive Shielding Paint

By

Verified Buyer


I purchased this for my 1967 Gibson SG (even though it has a metal shroud for pots/jack). Insulated pickup notches as well and works great. Thanks StewMac.

5.0

Black blacker blackest

By

Verified Buyer


I'm experimenting on electrifying my old wooden-body resonator and figured "Faraday Cage" was a good place to start: I'm talking coating the entire soundbox innards. This stuff covers easily, water soluble (easy-to-clean brushes), and after three coats offers up resistance in the teens (Ohms) so I am well-pleased. The one pint tin would easily do two guitars. Be sure to work in a ventilated area (I worked by an open window with a room fan sucking the air away) though because this can't be good for you! I am highly satisfied.

Showing 10 of 111 Read more reviews >>