Please see our COVID-19 Statement
Rear Peghole Reamer

Rear Peghole Reamer

Rear Peghole Reamer

Item # 2059
In stock, ready to ship!

$21.48

+
 
Total:
Qty:
Scroll to Top

Rear Peghole Reamer

About This Item

Counterbores the back of a 5/16"-diameter peghole to fit Grover and Gotoh sealed gear housing.

Here's a tip from our luthier friend Bryan Galloup: Grover and Gotoh tuners with threaded bushings should be installed in counterbored pegholes. A snug 5/16" diameter at the top of the hole stops the bushing from leaning under string pull, thus helping to protect the lacquer finish around the bushing washers. At Bryan's suggestion, we developed this special slow-speed steel reamer that accurately counterbores the bottom of the peghole to fit the gear housing.

The reamer has a .310"-diameter (7.87mm) pilot and two flutes that cut a .397"-diameter (10.08mm) counterbore in a 5/16"-diameter (7.94mm) peghole. When the reamer's piloted end is flush with the face of the peghead, the correct counterbore depth has been reamed.


CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
5.0
  • 4.95 average rating from 59 reviews
Sort by
5.0

Perfect tool to install Ratio machines

By

Verified Buyer


My circa 1970 Yamaha FG had a tuning machine on the low E with a gear so worn that it would skip a tooth, so I decided to upgrade to Ratio tuning machines. I found a clever method to pull the old bushings out with a 10/24 flat head machine screw, a rubber O-ring, a stack of 1/2" washers, a 1/4" washer, and a 10/24 wing nut. Cheap, quick, easy, and non-marring. This rear peghole Reamer worked great. I started by using my drill press to sand the tip of a 3/8" x 2" dowel pin down to fit the existing holes in the headstock. Then I drilled a 3/8" hole in a 2 x 4 clamped to my drill press and drove the dowel peg into that hole with just 3/16" of the tip exposed. Then I chucked this rear peghole reamer. Now, the dowel peg perfectly aligned each existing hole in headstock for reaming. This tool cut cleanly and precisely with no damage to the surrounding finish, and kept the front of the hole narrow to help prevent the tuning machines from tilting under string tension.

5.0

Best Purchase of 2020

By

Verified Buyer


This paid for itself the very first day! It takes all of the guess work and measuring out of drilling and installing tuners.

5.0

Peghole Reamer

By

Verified Buyer


Used this for my new Gotoh's, worked great! Marked the depth with painters tape prior to drilling so I didn't go too deep, totally satisfied!

5.0

Works great

By

Verified Buyer


First time using a peghole reamer, good quality and easy to use. Was done quickly and fit the new tuners perfect.

5.0

Perfect

By

Verified Buyer


I used this but with a hand drill and got great results.

5.0

Works great

By

Verified Buyer


Fast delivery the best way to prepare a Les Paul for Grover's.

5.0

Works as advertised

By

Verified Buyer


Got this to re-ream some vintage bore pegholes on a new tiltback neck to accept Grover Deluxe vintage-look sealed tuners.

Mounted a piece of plywood to my drill press to act as a depth stop for the tip of the reamer. Reamer was razor sharp. Worked perfectly. The tuners fit like a glove with just enough play to go in easy but not wiggle in the hole.

After stringing it up, the tuners worked fine.

My advice to anyone using this is use a drill press and WORK SLOW a little at a time. Make sure you clamp the peghead tight to your press so it doesn't move.

Who knows if I'll ever use it for another job, but it was cheaper then buying a new custom neck!

5.0

Floyd Rose Stud hole enlarger

By

Verified Buyer


I used this tool in an unconventional way, to make the Floyd Rose studs fit. (both are 10mm) High quality tool, works far better than a drill bit if using a power drill by hand.

I'll be using this to replace some guitar tuners as well. :-)

5.0

Makes Installation Simple

By

Verified Buyer


Very happy with this product.
Attached photo says it all.

5.0

Rear peghole reamer review

By

Verified Buyer


This thing is the cat's pajamas! Chucks up in a standard 3/8" drill chuck and with the pilot it bores down to the exact correct depth for the Grovers I installed. I clamped the headstock face down on my workbench and simply drilled until the pilot stopped it. 6 perfect holes in as many minutes. If you are even thinking of installing Grovers, add this to your order. You won't be sorry.

Showing 10 of 59 Read more reviews >>