Please see our COVID-19 Statement
Stewart-MacDonald Epoxy

Stewart-MacDonald Epoxy

Stewart-MacDonald Epoxy Fast setting, clear

Fast setting, clear

Item # 5173
In stock, ready to ship!

$13.68

+
Stewart-MacDonald Epoxy Slow setting, clear

Slow setting, clear

Item # 5174
In stock, ready to ship!

$13.68

+
Stewart-MacDonald Epoxy Slow setting, black

Slow setting, black

Item # 5179-B
In stock, ready to ship!

$20.35

+
 
Total:
Qty:
Scroll to Top

Stewart-MacDonald Epoxy

About This Item

Gap-filling epoxies for permanent bonds. Our high-strength 2-part adhesives are activated when their resin and hardener components are mixed in equal parts.

Each 4-ounce set has two 2-ounce bottles, ready for mixing.

Fast-setting mixture has 5-minute working time. Full bond strength in one hour.

Slow-setting mixture allows 20 minute working time. Full bond strength in 8 hours, for a rigid waterproof joint.

Slow-setting black mixture is great for inlaying ebony fingerboards. 20 minute working time. Wait 3 days before sanding.

Note: With all epoxies, the slower the setting time, the stronger the bond.

Use adequate ventilation and avoid skin and eye contact.

Keep out of the reach of children.


CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


Trade Secrets!

Trade Secrets!

Coloring epoxy for guitar inlays

A little bit of glue hides imperfections... Dan Erlewine personalizes a fretboard with the customer's name in pearl: "Hoss." There are small gaps around the inlays, and dan shows how to make those gaps disappear. Dan also shows a neat magnet trick for cutting thin slices off the end of a fretboard.

Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
4.5
  • 4.50 average rating from 44 reviews
Sort by
5.0

Stone Carver

By

Verified Buyer


I was looking for an epoxy to use with my stone carving to make small repairs or fill flaws in the stone with stone dust. This epoxy is clear and five minutes is the right amount of working time for my needs. The container allows for accuracy in mixing small amounts at a time. It seals easily and, importantly, without the risk of cross contamination. A great product!

This carving is called "Sheltering in Place"

5.0

Great for permanent neck set

By

Verified Buyer


I have always had good luck with Stew-Mac products and this does not disappoint. I have used this product before and it worked well.

5.0

epoxy

By

Verified Buyer


I've been using this for years. Good stuff.

5.0

Love the product and a quick tip.

By

Verified Buyer


I keep many grades of epoxy around for different jobs. I tend to use this for frets in worn out slots, repairing metal items, and filling. It is the perfect epoxy to use when you need something heavy bodied.

I noticed some comments about gelling in the bottle. I address this two different ways. If it is above 70 degrees outside, place the bottles in the sun for a half hour. Or put them in the sink and fill up the sink with hot tap water. Don't let it fill until the bottles topple over. They have to stand upright. Stop when you see the water line just about touch the epoxy level line in the bottle. Let warm for 10 minutes.

Warming the epoxy up will bring it back to its original fluid state.

For those that are using it in a spot that will be touched, and they don't like the somewhat tacky feel of the epoxy, sprinkle in some fumed silca. It will thicken up the epoxy a little, but gives it a rock hard dry feel.

5.0

Great Staff.

By

Verified Buyer


I love this products. Especially black one is good for Ebony as like a fingerboard.

5.0

Epoxy

By

Verified Buyer


Worked great to set in the neck to the body of my DIY 335 guitar.

5.0

Better than I imagined

By

Verified Buyer


I used this product because of the high heat value of 300°. There are a couple of brand named dryers that are known to have faulty drums and they crack. I bought one of them and fixed it completely. After pulling drum back together I added the epoxy to the outside of the drum first, let dry then a layer inside so the metal edge would not rip clothing. Smooth. Save $150 on drum replacement and the shipping of $80.
Keeping the rest on hand for some other projects that blind side me.

4.0

good glue

By

Verified Buyer


does what it says

5.0

Worked well for my purposes

By

Verified Buyer


Used the black epoxy to fill voids in claro walnut and it worked great. Let it harden and then scraped and sanded the surface flat. defects were virtually undetectable when done.

4.0

It's the Label

By

Verified Buyer


The epoxy works fine, it was just that both bottles were labeled 'part 1'. I guess it was just one of those little quality control things where two of the same labels got put on both part 1 and part 2 of the epoxy. I used it to glue in some abalone inlay-works just fine.

Response from StewMac


Hi Bruce,
We're sorry that both of the bottles of epoxy you received were labeled "Part 1 Resin", and apologize for any confusion this may have caused. Thanks to your comment, we have triple checked the epoxy in our inventory for this issue, and are happy to report all are labeled correctly now. If you ever need to contact us with an issue, our friendly Customer Support Team is available and always happy to help. Please feel free to give us a call at 1-800-848-2273.

Showing 10 of 44 Read more reviews >>