Please see our COVID-19 Statement
Pickguard Shielding Foil

Pickguard Shielding Foil

Pickguard Shielding Foil

Item # 0048
In stock, ready to ship!

$11.31

+
 
Total:
Qty:
Scroll to Top

Pickguard Shielding Foil

About This Item

Self-adhesive! Cut any size you need! Stick this aluminum shielding material to the underside of your pickguard to reduce noise, hum and radio interference.

The sheet is big enough to fully shield two Strat® pickguards, or cut it up to only cover the control cavity area (you'll be able to cover a LOT of cavities!).

20-3/4" x 13" x .003" (527.05mm x 330.2mm x .08mm)

Easy to trim, and self-adhesive so it's easy to apply—no gluing, no mess. A must-have for repair shops and guitar techs.

Note: Aluminum shielding will not accept solder. Use our Conductive Copper Tape for shielding jobs where solder connections are required.

Tip: For more complete shielding, line your pickup and control cavities with self-adhesive Conductive Copper Tape, or several coats of brush-on Conductive Shielding Paint. Extend a bit of the tape or paint outside each cavity and onto the top of the guitar, to make contact with your fully shielded pickguard. The control pots installed on the pickguard are the electrical ground connection for the shielding.


CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


Video

Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
5.0
  • 4.86 average rating from 35 reviews
Sort by
Displaying 2 of 4
1 2 3 4
5.0

Static Pick-guard Noise completely Gone!!

By

Verified Buyer


I bought the pick-guard shielding foil because my Vintage Fender 72 Telecaster Custom had a lot of pick-guard static which had made the guitar nearly unplayable due to the crackling and popping from the 3-ply pick-guard. The foil was easy to cut & fit to the back of the pick-guard and completely eliminated the static. Great product with the sticky back, no glue needed.

5.0

Easy to use

By

Verified Buyer


Very effective shielding, most outstanding feature is the ease of application, Foil thickness is ideal, adheres evenly, thick enough not to tear easily but cuts perfectly with a No, 11 blade.

5.0

Easy to Install and it works.

By

Verified Buyer


It was easy to install. I laid it out and trimmed with not problems. I cover the back of the pickguard with this and copper tape in the cavities and pickups. No more static electricity or other noise.

5.0

Kill That Pick-guard Static

By

Verified Buyer


I bought this foil in hopes of insulating the pick guard to kill the terrible static I was getting when touching the pick guard with my fingers. It has worked great reducing the horrible noise by 95%.

5.0

Excellant

By

Verified Buyer


Use this material for all pickguards.

5.0

Great quality

By

Verified Buyer


The shielding was nice and thick but still cut pretty easily. Adhesive held firm. There was more than enough for two pick guards.

4.0

does the job

By

Verified Buyer


A little difficult to work with but effective.

5.0

Pick guard insulation foil

By

Verified Buyer


This electronic insulation is ideal for my mods in my 89 Tele Plus!

5.0

Rice Krispies in a Gibson.

By

Verified Buyer


Used this along with Stew Mac Conductive Shielding Paint to stop static electricity from a 2016 Gibson SG pickguard and finish from producing audible 'crackles' while playing. Heard about a similar issue with a Jimmy Page model a few years ago too. Worked way better than putting a dryer sheet in the control cavity! (Who comes up with this stuff?)

5.0

Great for keeping things quite

By

Verified Buyer


Easy to use

Displaying 2 of 4
1 2 3 4
 
  • Stratocaster®, Strat®, and Squier® are registered trademarks of Fender Musical Instruments Corporation.