Please see our COVID-19 Statement
4-Conductor Circuit Wire - 16 inches

4-Conductor Circuit Wire - 16 inches

4-Conductor Circuit Wire - 16 inches

Item # 5953
In stock, ready to ship!

$2.97

+
 
Total:
Qty:
Scroll to Top

4-Conductor Circuit Wire - 16 inches

About This Item

Shielded 4-conductor hookup wire. Used to gain tonal flexibility, allow coil cuts, combine the coils in series or parallel, or wire the coils in or out-of-phase.

Reduce unwanted electrical noise by using shielded wire for your longer wiring runs (for example, the connection between the controls and the output jack). This shielded wire contains inner copper conductors covered with polyethylene insulation, which is surrounded by an outer conductive shield, which is connected to ground. The black outer jacket material is PVC.

Also available in 25-foot lengths.

28AWG
Tinned copper conductor
Foil shield with tinned copper ground wire
0.120" (3.05mm) outer diameter
Sold pre-cut into 16" (406mm) lengths

Save over 20% when you buy 25-feet of 4-Conductor Circuit Wire.

For short connections between components, use Non-shielded Guitar Circuit Wires or our Vintage Push-Back Wire.


CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
5.0
  • 4.79 average rating from 14 reviews
Sort by
3.0

Toggle Switch wire

By

Verified Buyer


I had bought this wire for my new toggle switch, I was switching out my Les Paul's pc board and cables. Once I received my order I saw how small the the 4 conductors were and I also felt the length was very close to being to short, maybe if my soldering skills were better i would have thought different. I ended up ordering more than enough shielded single conductor to wire it up.

5.0

Good Stuff

By

Verified Buyer


4 conductor wire with a bare lead for grounding hookups excellent quality with an additional foil wrap under the insulation to aid in shielding. Wire is good quality although a good wire stripper is recommended as the single insulation on the wires is a bit sturdy but can be pared back with a sharp knife. This is perfect wire for modern humbuckers letting customers chose the wiring set up of their liking (traditional humbucking or coil tap) There is ample length here to make the most demanding runs. As far as flexibility is it a bit stiff but will make fairly sharp turns if prodded. All in all this is good stuff.

5.0

much easier

By

Verified Buyer


This makes wireing so much easier.

5.0

Works great for humbuckers

By

Verified Buyer


Used this to replace a too short lead on an old Swineshead humbucker, and it worked great.

5.0

Good choice for 5-wire pickup repairs.

By

Verified Buyer


I used it to rewire a 5-way Fender "Super Switch" and it worked great!

5.0

Just what the doctor ordered

By

Verified Buyer


Needed a 4 wire conductor wore for my explorer build from switch to the controls. Perfect length.

4.0

Smaller than I thought

By

Verified Buyer


I should have paid closer attention to the gauge. I was looking for a heaver gauge of wire. Good quality though.

5.0

Four Goodness Sake!

By

Verified Buyer


Pretty straightforward little item that does what it is supposed to and does it very well. I also like that they have detailed instructions on their website about how to wire up the bucker to this. It's good to be able to look in and sense check yourself as you are working late nights and you can't see the wood for the trees.

5.0

Better than original.

By

Verified Buyer


Rewired a short clipped 2 conductor neck pickup and changed it to 4 conductor for coil splitting.

5.0

Just what I needed.

By

Verified Buyer


I purchased these to rewire some Seymour Duncan pickups. They worked great!

Showing 10 of 14 Read more reviews >>