Please see our COVID-19 Statement
Mojotone Amplifier Chassis Stand

Mojotone Amplifier Chassis Stand

Mojotone Amplifier Chassis Stand

Item # 10750
In stock, ready to ship!

$157.45

+
 
Total:
Qty:
Scroll to Top

Mojotone Amplifier Chassis Stand

About This Item

Service and build your amp like a pro
Mojotone's Amp Chassis Stand holds your amp the right way.

Working on your amp is difficult. There are fragile turret and PC boards, circuit traces, and tiny eyelets that are hard to see. You need a solid stand to make clean solder joints and lay out the best signal flow. This stand holds the chassis in place, with or without tubes, so you can fix issues and install components easily.

Work on your amp safely
The Mojotone Amp Chassis Stand is made of Baltic Birch so that it will not conduct current, a danger when working on amps. It's height and width are adjustable to hold nearly any amp chassis (up to 29-3/4" long). Each side locks in place to ensure your amp won't move during work. You can also change the angle of the chassis 180 degrees to get the perfect view. Essential for amp building.

Be your own amp tech with Mojotone's Amp Chassis Stand

Some assembly required.


CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
4.5
  • 4.63 average rating from 8 reviews
Sort by
4.0

Good but with limitations

By

Verified Buyer


Think about this like a circuit board/eyelet board holder you may use for soldering, Same thing, securely holds an amp chassis so you can work on it. Great concept, particularly for amps or effects units that might have tube sockets or transformers hanging down that make the chassis hard to keep stable directly on the bench. I've found this holds chassis very securely and it's easy to adjust angle for best component access.
Things to think about: Some chassis just won't fit because of component placement. Some chassis have holes that will be hard to work with when held.
Also, and my main problem, this raises your chassis 6-8 inches (depending on the chassis design) higher off your workbench. This can make it harder to reach over and solder. And finally, it is big, takes up a lot of bench space that you might not have, measure carefully.
I'm using it and happy with it, but work with the limitations. I also realize I've used the word "chassis" more times in one 2 paragraph entry that I've ever one before....

5.0

Mojotone Amplifier Chassis Stand

By

Verified Buyer


JP-- Florida: Well thought-out design and high quality. It has quite a personality.

4.0

Works good

By

Verified Buyer


I purchased this for a Brit Plex 45 kit build, It does work good, there are a few things that are difficult to do with it. That being said, maybe by the time I am actually done with my build I will have more experience using. I don't think I would of liked to try to build my amp without it though.

4.0

Works great after you have the chassis in there

By

Verified Buyer


The only problem with this tool is that when it is flat on the bench surface you cannot move the pieces that hold the chassis because they are hitting the bench. I would recommend you put a piece of wood under each end so you can move the chassis holders easily.

5.0

Made my first amp build a lot easier

By

Verified Buyer


I bought this for my first amp build, a 5e3 clone. It made assembly a lot easier to tilt the chassis to different angles. This thing is huge, about twice as big as I thought it was from the photos. Very well built, but the recessed nuts comprising the mechanism could use some improvements...however, this did not detract from the usability.

One note for the 5e3...the transformer sits close to the edge of the chassis, and means that only about 1/4" of one side of the chassis is on the cradle. I emailed Mojotone, and they said the 1/4" would hold it fine, and they were right. They also suggested installing the power transformer at the end.

Now that I have this, will need to build some more amps!

5.0

Very Useful and Well Made

By

Verified Buyer


Very helpful to have chassis locked into position and raised above the workbench. Very sturdy and has worked well with chassis of differing depths, widths and configurations. T-nuts used to lock adjustments could do with an upgrade but don't detract from overall usefulness.

5.0

Does what I need it tyo do

By

Verified Buyer


Well built.
I made one modification.
I added handles to make it easier to move around.

5.0

Great for amp work !!

By

Verified Buyer


This product is well worth the investment if you work inside of amps a lot. Especially tube amps.
Being able to rotate the chassis while tubes are inserted and you are taking measurements is a huge plus. It's heavy duty and well constructed. Definitely a must for the amp builder!!