Conductive Shielding Paint

Conductive Shielding Paint

Conductive Shielding Paint 1/2 pint (236.6ml)

1/2 pint (236.6ml)

Item # 0029
In stock, ready to ship!

$35.84

+
Conductive Shielding Paint 1 pint (473.2ml)

1 pint (473.2ml)

Item # 0027
In stock, ready to ship!

$66.13

+
California Residents: Click here for Proposition 65 information.
 
Total:
Qty:
Scroll to Top

Conductive Shielding Paint

About This Item

Reduces hum, noise and radio interference.
The fastest and easiest way to shield pickup and control cavities. Perfect for tight spots.

When connected to electrical ground, the shielded surfaces help reduce noise, hum and radio interference. It cleans up with water while still wet, and dries overnight.

Brush on two or more coats of this waterbase dark gray conductive paint for best results (let dry between coats). Conductive shielding paint is supplied in a 1/2-pint can, sufficient for shielding several electric guitars, and in a money-saving 1-pint can. We recommend our conductive tape for best results when shielding smooth plastic pickguards.

Instructions

Product Instructions

Conductive Shielding Paint Instructions

Directions for using conductive shielding paint.

Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
5.0
  • 4.82 average rating from 87 reviews
Sort by
5.0

Shielding Paint

By

Verified Buyer


3 coats per instructions, testing proves conductivity. Plenty leftover for other guitars.

5.0

Buzz and hum are gone

By

Verified Buyer


I watched numerous videos on what caused the noise from my Telecaster. The solution was to shield the cavities of my guitar. I followed the dirrections by applying three coats of this paint, allowing it to dry 24 hours between coats; stir the paint well and don't shake the can. To get the paint in the hole for the bridge pickup to the pots, I used a Q-tip (it worked well; paint that first.) A 1/2 inch brush was the right size for everything else. Be sure to mask everywhere you don't want the paint to go. After this, I checked the continuity between the pickup cavities and the control cavity, everything was good. I also put a ground wire from each pickup to the cavity wall and from one of the pots to the cavity wall. Then, I shielded the back of the pick guard with alluminum foil. This Telecaster has never been so quiet! I can barely tell my amp is on, even when it's cranked up.
The paint may seem a bit pricey, but, it's worth every penny. AND, there is enough left to do my other Telecaster and my Strat.
Thank you Stew Mac for making this product available

5.0

Conductive Shielding Paint 1/2 pint can.

By


There is a LOT of paint in this little can. You can do more "Gitirs" than you planned for.

5.0

Say buh bye to noise problems

By

Verified Buyer


I've used foil and copper to line the body cavities of my guitars before, with good success, but this stuff is worth the price. So much easier, and after 6 coats, I got strong connectivity with my mulitimeter no matter where I tested. No Grounding noise problems, no problems with shielding and noise interference...

One small can put 6 coats of paint inside the body cavities of two stratocasters with swimming pool routs.. and I still have half the can. Don't waste time and effort with foil and tape. Just use the stuff that's meant to be there.

5.0

WORKED GREAT

By

Verified Buyer


Product worked as described - 3 coats around the pickups and internal routed area of my new bass - quiet as a mouse now.

5.0

Great stuff

By

Verified Buyer


Used this on a 35 year-old P bass refurb project ... used to be really noisy ... rewired and shielded body. Did 3 coats over one of primer. Suspect can will do several guitars, I barely put a dent in it doing one. Worked very well.

5.0

It works great

By

Verified Buyer


This worked great for me. I used this in a P Bass guitar. Put on the three coats as recommended. Make sure to stir between coats. Took care of the noise and buzz that I had.

4.0

good product

By

Verified Buyer


I Used this and the copper tape -- Had very good results. Easy clean up but took a few coats. No Hum

5.0

Shielding paint.

By

Verified Buyer


Easy to use and effective.

5.0

Miracle stuff

By

Verified Buyer


I received a high end bass guitar with a HORRIBLE buzz. Swapped pick ups, pots, and wiring. Even shielded cavities with hardware store aluminum tape which usually does the job. But no luck. This paint saved the day. I did 4 coats on the cavities and passage ways for the wiring. The guitar is now silent!!!! I'm not kidding!!! This paint is the real deal.
Fantastic!!! Thank you Stew.

Showing 10 of 87 Read more reviews >>
 


StewMac PDF Catalog, page 54 See Conductive Shielding Paint
on page 54 of our StewMac Digital Catalog