Special Stock Mighty Mite Birdseye Maple Neck for Tele Guitar

Special Stock Mighty Mite Birdseye Maple Neck for Tele Guitar


Special Stock Mighty Mite Birdseye Maple Neck for Tele Guitar

Item # 15717
No longer available


Sold Out
Scroll to Top

Special Stock Mighty Mite Birdseye Maple Neck for Tele Guitar

About This Item

Limited Supply! Top quality Fender-licensed necks from Mighty Mite
We managed to get our hands on a small stash of amazing Birdseye Maple Fender® Tele replacement necks from Mighty Mite and we're passing the savings on to you!

Through our close connection to top factories and manufacturers around the world, we're constantly on the lookout for irresistible deals we know our customers will love—but there aren't many of these, so when they're gone, they're gone!

Shaped, inlaid, fretted and finished—they're ready to install! These are not your ordinary maple necks, these Hard Rock Maple (Acer saccharum) necks have beautiful Birdseye figure on the neck and fingerboard. Each is professionally finished in clear satin polyurethane, with an inlaid merbau "skunk stripe" down the back.

The 22 medium frets are nicely seated, crowned, and polished. The installed PPS plastic nut has a flat bottom and is slotted and ready to play. The fretboard is inlaid with black dots.

The screwholes for attaching to the body are not drilled—you can fit this neck to any mounting pattern you want. Each neck has a single-action truss rod with a 4mm adjusting nut at the peghead. We recommend Allen Truss Rod Wrenches for adjusting neck relief.

The peghead is drilled for 6-in-line tuning machines. The 10mm-diameter holes fit sealed gear tuners with threaded bushings. See all our tuners. and find the perfect set for you.

    Ready to build features:
  • Thin polyurethane finish
  • 22 medium frets
  • C shape
  • Birdseye Maple neck and fingerboard
  • Peghead-adjustable truss rod (for 4mm Allen wrench)
  • Black dot inlays
  • 10mm diameter pegholes
  • No mounting holes drilled—you can drill them to fit your body

Scale length: 25-1/2" (647.70mm)
Width at nut: 1-5/8" (41.28mm)
Width at 22nd fret: 2-3/16" (55.56mm)
Fretwire: 0.045" high x 0.100" wide (1.14mm x 2.54mm)
Approximate heel length: 3-5/8" (92.07mm)
Fretboard radius: 9-1/2" (241.30mm)
String post spread: 4-11/16" (119.06mm)
Fits neck pockets: 3" x 2-3/16" x 5/8" (76.20mm x 55.56mm x 15.88mm)

Neck Thickness:
At 1st fret: 0.835"
At 6th fret: 0.865"
At 12th fret: 0.900"

Ideally, the neck should just drop into the neck-pocket, or be a little snug. Don't force the neck into the pocket. If the body is unfinished, remember that the finish will make the neck pocket smaller with lacquer build up on the edge of the rout. Be sure to compensate for the finish buildup or the neck will be too tight after finishing.

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Customer Reviews

Write a review
  • Not rated yet
  • These necks are made for us by Mighty Mite®, and have peghead shapes licensed by Fender®.
  • Telecaster®, Tele®, and Esquire® are registered trademarks of Fender Musical Instruments Corporation.