Special Stock Mighty Mite Neck for Jazz Bass

Special Stock Mighty Mite Neck for Jazz Bass

Special Stock Mighty Mite Neck for Jazz Bass Maple Fingerboard

Maple Fingerboard

Item # 15719
In stock, ready to ship!


Special Stock Mighty Mite Neck for Jazz Bass Indian Rosewood Fingerboard

Indian Rosewood Fingerboard

Item # 15720
In stock, ready to ship!


Scroll to Top

Special Stock Mighty Mite Neck for Jazz Bass

About This Item

Limited Supply! Top quality Fender-licensed necks from Mighty Mite
We managed to get our hands on a small stash of fast playing Fender® Jazz Bass replacement necks from Mighty Mite and we're passing the savings on to you!

Through our close connection to top factories and manufacturers around the world, we're constantly on the lookout for irresistible deals we know our customers will love—but there aren't many of these, so when they're gone, they're gone!

Shaped, inlaid, fretted, and finished—they’re ready to install! These are not your ordinary maple necks, these Hard Rock Maple (Acer saccharum) necks have the classic fast Fender Jazz Bass profile.

Each is professionally finished in clear satin polyurethane, with a maple fingerboard inlaid with a merbau "skunk stripe" or Indian Rosewood fingerboard with matching Indian Rosewood "skunk stripe" down the back. The installed PPS plastic nut has a flat bottom and is slotted and ready to play. Inlaid with white or black dots, this neck is ready to install right out of the box. The 20 medium frets are nicely seated, crowned, and polished.

The screwholes for attaching to the body are not drilled—you can fit this neck to any mounting pattern you want. Each neck has a single-action truss rod with a 4mm adjusting nut at the peghead. We recommend Allen Truss Rod Wrenches for adjusting neck relief.

The peghead is drilled for 4-in-line tuning machines. The 11/16" diameter (18mm) holes fit many popular bass tuners. See all our tuners. and find the perfect set for you.

    Ready to build features:
  • Thin polyurethane finish
  • 20 medium frets
  • Jazz Bass C shape
  • Maple neck
  • Indian Rosewood or Maple fingerboard
  • Peghead-adjustable truss rod (for 4mm Allen wrench)
  • Dot inlays
  • 11/16” diameter (18mm) pegholes
  • No mounting holes drilled—you can drill them to fit your body

Scale length: 34" (863.60mm)
Width at nut: 1-1/2" (38mm)
Width at 20th fret: 2-1/2" (63.50mm)
Fretwire: 0.040" high x 0.100" wide (1.01mm x 2.54mm)
Approximate heel length: 4-1/2" (114.3mm)
Fretboard radius: 9-1/2" (241.30mm)
String post spread: 5-9/16" (141.28mm)
Fits neck pockets: 3-7/8” x 2-1/2” x 5/8" (98.43mm x 63.50mm x 15.88mm)

Neck Thickness:
At 1st fret: 0.820"
At 6th fret: 0.840"
At 12th fret: 0.890"

Ideally, the neck should just drop into the neck-pocket, or be a little snug. Don't force the neck into the pocket. If the body is unfinished, remember that the finish will make the neck pocket smaller with lacquer build up on the edge of the rout. Be sure to compensate for the finish buildup or the neck will be too tight after finishing.

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Customer Reviews

Write a review
  • Not rated yet
  • Jazz Bass® is a registered trademark of Fender Musical Instruments Corporation.
  • These necks are made for us by Mighty Mite®, and have peghead shapes licensed by Fender®.