Special Stock Mighty Mite Fretless Neck for Precision Bass

Special Stock Mighty Mite Fretless Neck for Precision Bass

New!

Special Stock Mighty Mite Fretless Neck for Precision Bass

Item # 15718
In stock, ready to ship!

$154.00

+
 
Total:
Qty:
Scroll to Top

Special Stock Mighty Mite Fretless Neck for Precision Bass

About This Item

Limited Supply! Top quality Fender-licensed necks from Mighty Mite
We managed to get our hands on a small stash of ready to play fretless Fender® Precision Bass replacement necks from Mighty Mite and we're passing the savings on to you!

Through our close connection to top factories and manufacturers around the world, we're constantly on the lookout for irresistible deals we know our customers will love—but there aren't many of these, so when they're gone, they're gone!

Shaped, finished, and ready to install! These are not your ordinary maple necks, these Hard Rock Maple (Acer saccharum) necks have a highly polished fretless Ebonol fingerboard. Ebonal has long been used for fretless basses for its durability and fast feel.

Make your own fretless bass
Each is professionally finished in clear satin polyurethane, with an inlaid merbau "skunk stripe" down the back. The side dots are moved to the fret line locations, making it easier to know where you are if you normally play fretted basses. The installed PPS plastic nut has a flat bottom and is slotted and ready to play.

The screwholes for attaching to the body are not drilled—you can fit this neck to any mounting pattern you want. Each neck has a single-action truss rod with a 4mm adjusting nut at the peghead. We recommend Allen Truss Rod Wrenches for adjusting neck relief.

The peghead is drilled for 4-in-line tuning machines. The 11/16" diameter (18mm) holes fit many popular bass tuners. See all our tuners. and find the perfect set for you.

    Ready to build features:
  • Thin polyurethane finish
  • Fretless Ebonol fingerboard
  • Precision Bass C shape
  • Maple neck
  • Peghead-adjustable truss rod (for 4mm Allen wrench)
  • Side dot inlays
  • 11/16" diameter (18mm) pegholes
  • No mounting holes drilled—you can drill them to fit your body

Specifications:
Scale length: 34" (863.60mm)
Width at nut: 1-5/8" (41.28mm)
Width at 20th fret location : 2-1/2" (63.50mm)
Approximate heel length: 4-1/2" (114.3mm)
Fretboard radius: 16" (406.4mm)
String post spread: 5-9/16" (141.28mm)
Fits neck pockets: 3-7/8" x 2-1/2" x 5/8" (98.43mm x 63.50mm x 15.88mm)

Neck Thickness:
At 1st fret: 0.850"
At 6th fret: 0.860"
At 12th fret: 0.900"

Ideally, the neck should just drop into the neck-pocket, or be a little snug. Don't force the neck into the pocket. If the body is unfinished, remember that the finish will make the neck pocket smaller with lacquer build up on the edge of the rout. Be sure to compensate for the finish buildup or the neck will be too tight after finishing.



CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


Customer Reviews

Write a review
0.0
  • Not rated yet
 
  • These necks are made for us by Mighty Mite®, and have peghead shapes licensed by Fender®.
  • Precision® Bass and P-Bass® are registered trademarks of Fender Musical Instruments Corporation.