StewMac Luthier's Square

StewMac Luthier's Square

StewMac Luthier's Square

Item # 4958
In stock, ready to ship!

$24.14

+
 
Total:
Qty:
Scroll to Top

StewMac Luthier's Square

About This Item

Precision steel square for instrument work
Square up parts, lay out string spreads, and accurately set up tools. 1/32"-increments on one side, millimeters on the other.

Lies flush on guitar tops
Unlike squares with a thin blade and thick handle, our Luthier's Square works flat against a guitar's surface.

Set up tools, true up parts
The small size is handy for tight spots. The notched inside corner fits against corners snugly, with no wobble.

Measure nuts, saddles and pickups
Small vertical rulers are useful for measuring height on saddles, nuts, and pickups.

Easy to read
Satin chrome steel with sharp black etchings reads well even in poor light. Accepts pencil marks nicely, too.

  • 4" ruler (10cm)
  • 0.040" (1.02mm) thick satin chrome steel


CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
5.0
  • 4.71 average rating from 24 reviews
Sort by
Displaying 2 of 3
1 2 3
5.0

Nice to have on hand

By

Verified Buyer


Nice to have a square this size in my shop.. priced right too

5.0

Great Square

By

Verified Buyer


This is one of the best tool purchases I have made from Stew-Mac. Very Handy to have in the tool kit. Have used it quite a bit since receiving a few weeks ago....

5.0

Great for tool box

By

Verified Buyer


I was pleasantly surprised when I received this square. It's smaller than I expected but perfect for use with several guitar repairs and. checks.

4.0

Very Useful

By

Verified Buyer


A lovely machined tool with a lot of heft. Obviously very accurate. My only problem with these type of tools is that the corners are sharp as razors and can be a menace to wood and finishes. Obviously these measuring tools have to have sharp corners, but beware and be careful around tender wood or a new finish or you are going to make a nasty scratch.

4.0

Metric on back

By

Verified Buyer


I wish it had imperial measurements on the back instead of metric. I feel most people use one or the other, not both. Maybe they could sell two squares an imperial for the stubborn US and Metric for the rest of the world.

5.0

StewMac Luthier's Square

By

Verified Buyer


Great for setting router bit heights using the scale on the toe of the square.

5.0

The Magic Square!

By

Verified Buyer


Incomparable to transfer center lines from edges perfect to mark the easy brace notches on the easy outside curve and even "perfecter" on the tricky angled inside curve! Very good tool!

5.0

Great Little Square

By

Verified Buyer


I have about 5 squares, but they're all to big for some of the closer, tight work I need to do on a neck or body. This square is perfect for those tight places.

Ironworxx Guitars

5.0

A sweet and useful tool

By

Verified Buyer


This is a sweet and useful tool. I used it to square up the blade on my table saw without knocking off the the little burr on the test board's edge after every trial cut. It has replaced my cute little 4" Starrett combination square as the most frequently use tool in my shop. I'd get another one, but I only have two hands and couldn't use both simultaneously! Maybe some good friend needs one as a gift . . .

4.0

Close

By

Verified Buyer


This is a very handy square, the size and end graduations are just what I wanted. I would rather that it was all inches or all metric though. When I use it to measure and have to turn it left to right it leaves me with different scale, frustrating.

Bill

Displaying 2 of 3
1 2 3
 


StewMac PDF Catalog, page 32 See StewMac Luthier's Square
on page 32 of our StewMac Digital Catalog