Trade Secrets!

Rugged and road-ready: replacing skimpy parts


Issue 143 July 07, 2011

They built this guitar rugged, but they skimped on the parts!

Hondo guitar

2 easy fixes made this Hondo ready to rock


My pal John Garris got a good deal on this super cool Hondo from the 1970s.

He’ll use it as a second guitar on stage with his band Wheels on Fire. John loves it; he says it reminds him of the “TV finish” Les Paul Juniors Johnny Thunders played during his short career with the New York Dolls and The Heartbreakers.

Make it road-ready

Weak parts on a strong guitar

These old Hondos were budget alternatives to the big brands of the 70s. Hondo didn’t skimp on the build quality; this guitar is solid as a tank. But I think the hardware and electronics are where they cut corners. Those parts seem a little flimsy.

As-is, this guitar would be fine for a player who just plucks around occasionally. But John tours the world with Wheels on Fire and he needs guitars he can depend on night after night. To make this one road-ready required beefing up two weak points: the bridge and the tuners.

Problem 1: misplaced bridge

The thing that concerned me most was the bridge. The locations of the mounting posts seemed iffy, since the bridge had to be kicked way back on its adjustments just to get it to play in tune. Notice the completely extended adjustment screw at left. And even at this, it wouldn't intonate quite right.

Bridge adjusting screw

With the adjustment screw cranked out so far, the bridge teetered forward at an angle you can see in the photo at left. And it buzzed. We decided to replace the bridge with something more suitable. I chose the Pigtail bridge/tailpiece because it has a wider intonation range than the stock bridge.

Tipped bridge
See this album on our Facebook photos pageSee this album on our Facebook photos page See this album on our Facebook photos page

In the photos below I'm filing the saddle slots, then flossing them smooth with abrasive cord. The Pigtail bridge worked out great: the saddles adjusted back far enough for good intonation while allowing the meat of the bridge to contact the mounting posts. This gives good transfer of string vibration from the bridge to the body.

Installing a Pigtail bridge
Installing a Pigtail bridge

I replaced the posts with TonePros locking studs to hold the bridge nice and tight, and parallel to the body.

Installing a Pigtail bridge

Now for Problem 2: sloppy tuners

Now the bridge can be intonated, so it’s possible to really tune the guitar. But we have another tuning trouble at the other end of the strings: the old tuning machines are loose, and they slip a lot. That’ll never cut it onstage.

Bad tuners!

I recommended that we swap out the original tuners for something bulletproof: Grover Rotomatics.

I eased out the old tuner bushings without adding more chips to the peghead face by using a tuner bushing press.

Installing tuners
Installing tuners

On the back of the peghead, I reamed the pegholes so they’ll fit the Grover tuners.

Reamed the pegholes so they’ll fit the Grover tuners
Reamed the pegholes so they’ll fit the Grover tuners

Here’s a tip:

When you’ve carefully reamed the first tuner hole to the depth that gives you a good fit, mark your reamer with a permanent marker. You can see the line I drew around the peghole reamer in the photo above. Now you can blitz through the five remaining holes without trial-and-error: ream them until your mark is flush with the surface.

Depth-stop bit:

Check out the white depth stop on the drill bit above. It’s built onto the bit, and it prevents me from drilling my tuner mounting holes too deep, or right through the peghead. That’s a prototype of a new product we have in the works, letting you drill more holes faster, without slipups. Look for these bits in our next free catalog!

The original electronics were replaced by the previous owner. It has a Seymour Duncan pickup, which John’s really happy with. So, “If it ain’t broke, don’t fix it.”

I like my pickup

The last step was a thorough setup, adjusting the action, intonation and height of the pickup polepieces. This guitar’s ready to rock, and I’ll be dropping it off to John at the club tonight.

Final setup

And here’s John onstage, loving his new old Hondo!

John Garris on stage