Stud/Bushing Set for Stop Tailpiece

Stud/Bushing Set for Stop Tailpiece

Buy more, save more!
Stud/Bushing Set for Stop Tailpiece Nickel

Nickel

Item # 0186-N
In stock, ready to ship!

$10.98

3 or more $9.33
+
Stud/Bushing Set for Stop Tailpiece Chrome

Chrome

Item # 0186
In stock, ready to ship!

$11.10

3 or more $9.43
+
Stud/Bushing Set for Stop Tailpiece Gold

Gold

Item # 0186-G
In stock, ready to ship!

$11.91

3 or more $10.12
+
 
Total:
Qty:
Scroll to Top

Stud/Bushing Set for Stop Tailpiece

About This Item

Replacements available to refurbish or replace the post and bushings on your stop tailpiece or wraparound bridge. M8 x 1.25 thread. Sold in sets of 2.

Use an 11mm drill bit to install the bushings.


CALIFORNIA PROPOSITION 65 WARNING
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.


    • Item #
    • Weight
    • 0186
    • 0.0965 lbs. (0.04 kg)
    • 0186-G
    • 0.1130 lbs. (0.05 kg)
    • 0186-N
    • 0.1130 lbs. (0.05 kg)

Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
4.5
  • 4.40 average rating from 10 reviews
Sort by
5.0

Worked well

By

Verified Buyer


Just needed the studs to replace scratched ones. They fit well and look great.

5.0

perfect fit

By

Verified Buyer


studs threaded into maestro mini V without replacing bushing.

3.0

Too small, too short

By

Verified Buyer


Bushing is too small outside diameter to fix Epiphone Korean Les paul. It just drops in the bushing hole with a lot of slack. Smaller than the original. Also the post is not as long as the post that comes on the Epiphone Korean Les Paul. There is also slack in the fit from post to the bushing thread. Sloppy fit there. This kit is not suitable to repair leaning stop tailpiece for me. I thought that since the bushing is longer it would be better for my repair. But my mistake was not being clear on the other specs. I assumed that since it was M8 X 1.25 that the other specs would match too.

Response from StewMac


Hi M L,
We're very sorry to hear our Stud/Bushing Set for 'Stop' Tailpiece wasn't the right fit for your guitar. Quality and 100% Total Satisfaction is our goal every day. If you are not satisfied with a product, you are welcome to return it for a refund or exchange. Our friendly Customer Support Team is always here to help at 1-800-848-2273 if you would like to address this issue further.

5.0

up grade

By

Verified Buyer


change damaged ones on my own guitar

4.0

They are well done

By

Verified Buyer


I only wish you had a 5/16 version, replacing these on a 77 Gibson firebird, I found the bushings way to small, Had to tap the originals to M8 and thread the stud up to the top

4.0

as good as new

By

Verified Buyer


They look and feel like the original

4.0

They do the job

By

Verified Buyer


First of all, consider to buy this product if you are planning to replace the posts and bushings on your stop tail. If you try to use only the posts and the old bushings on an american made SG or LP they are not going to fit. The thread is different. But the product itself is good quality and would do the job if you replace everything that hold your stop tail in place!

5.0

Perfect

By

Verified Buyer


I used these to fix broken tailpiece studs on a Gibson Maestro Mini V. They did the job perfectly with little effort.

5.0

bonne qualitT

By

Verified Buyer


piFces de remplacement de bonne qualitT

4.0

Basic, but dependable

By

Verified Buyer


I purchased a set of these to replace a set of TonePro's Locking Studs that broke when I installed them (read my other review under that product). The head on one them twisted off as I was tightening it. These studs are basic and don't have the locking feature, but they are strong and serve their purpose just fine.

 


StewMac PDF Catalog, page 90 See Stud/Bushing Set for Stop Tailpiece
on page 90 of our StewMac Digital Catalog