Stewart-MacDonaldEverything for building and repairing stringed instruments!
Your order cart Your order | Account | Saved list
Sign in
Email
800-848-2273, 9AM-6PM EST, M-F
Home Free catalog Quick order International Customer service

Home : Trade Secrets Archive : Issue 159, A neat trick for drilling perfectly centered holes in guitar tuners
Trade Secrets NEWSLETTER
Email a friend









 Processing...






Image: Trade Secrets banner
Dan on TV
Hot tip: YouTube video from Dan Erlewine  
 
  “Here’s a really neat trick for
drilling perfectly centered holes.”
 
 
  This tip is perfect for drilling guitar tuner knobs,
and I’ll bet you’ll find other ways to use this idea.
 
  Dan Erlewine, March 1, 2012  
When plastic tuner knobs get really old, they eventually rot away. This happened to some tuners my friend Spencer Bohren sent me. One set was from his old Supro lap steel (I worked on that guitar in Trade Secrets #150). The other set dated all the way back to 1897, on Spencer’s Bruno parlor guitar. (Those 19th-Century knobs were probably made of celluloid.)


Rotten tuner knobs Brown, crumbly trouble. These rotted old buttons are starting to crack right off their shafts. Spencer asked me if I could replace them, and doing the job right involved a neat drilling trick I’d like to show you. I made a short video showing how I did this very common job. On the video, I worked on both sets of tuners; here I’m working on the Supro tuners only.
See our Trade Secrets archive
3-on-plate replacement tuners The easy way: Our vintage 3-on-a-plate tuners are a direct replacement. They’re an exact fit, and they work better than the originals did when new.
But Spencer wanted to keep the old vintage tuners working, and I like a challenge, so I agreed to do this the hard way. Here we go...
Vintage-style 3-on-Plate Tuners
Cutting off the old knobs Bite off the old: Fret cutters snip away the knobs, neat and clean. When you get close to the shaft, “nibble” until the last of the plastic comes free. Clean up the exposed shafts with a wire brush, then degrease them with naphtha.
Fret Cutter
Link to see video
Round peg, square hole Just like the old Kluson knobs, our vintage replacement knobs have a rectangular hole. The tuner shaft is heated and pressed into this hole, melting its way in.
The shaft is round, with a spear-shaped end. Fitting that round shaft into a slot-shaped hole is mighty tight, so I prefer to alter the hole for a better fit. I drill a round hole in the center of the rectangle.
The shaft measures approximately .136"; I drill a smaller hole (.104") using a #37 drill-bit. The knobs go on easier, and since the hole is smaller than the shaft it’s still a snug fit.
But it’s tricky.
Vintage-style Tuner Knobs
Drilling the tuner knob

Drilling a hole exactly in the center of a rectangle is hard to do without this tip: a “centering stick” for positioning the knob exactly right below my drill press chuck. I slightly flattened one end of a length of 1/8" diameter hollow brass tubing by squeezing it in my nut and saddle vise. I filled the end with hot solder, and filed it until it fit the rectangular shape of the hole.
I chucked this tube, with the knob on it, into my drill press. I lowered the knob into the nut/saddle vise and gripped it there, then lifted the drill chuck. This pulled the tube out, leaving the knob perfectly located for drilling. I put a drill into the chuck, and drilled the hole exactly on center. A piece of masking tape served as a depth stop marker.

Nut and Saddle Vise
Perfectly centered hole The hole is right on dead center. This knob will fit the shaft perfectly.
I drilled six more knobs with this setup; that gave me one extra in case I mess up when installing them on the shafts.
 
Heating the tuner, installing the knob Heat from a soldering gun. I heat the shaft with a Weller soldering iron. I've modified the gun’s tip by cutting its copper loop. The gun won’t heat unless this tip’s circuit is intact; when the two cut ends touch the shaft, the circuit is completed and the metal gets hot quickly. You can also use a regular soldering iron for heat, as long as it’s at least 30 watts.
When the metal's hot, start the knob onto it by hand (be careful, I should’ve been wearing gloves). Then quickly get it into the vise and use it to squeeze the knob on. I have a scrap of aluminum channel in the vise to focus the pressure on the end of the shaft, sparing the sheet metal gear housing.
You’ll feel the pressure give all of a sudden, as the knob slides home.
StewMac Super Glue
Super glue pipette A little insurance. Once the knobs are on, I run water-thin #10 super glue down the shaft to fill any gaps and make the joint even stronger. I use a pipette, but for better reach and a lighter flow of glue, I cut the pipette’s tip off and replace it with a whip tip.
Pipettes
Whip Tips
Old vs. new tuners It’s surprising how sometimes a set of old Klusons will be shiny and clean even though the knobs are so rotten. With the new knobs, these tuners (on the left) look nearly new — almost like this set of new Stew-Mac tuners. If this were my guitar, I’d use the smoother-working new ones because they tune more accurately.
 
Problem-solving products for this kind of work:
Fret Cutter
The best tool for cutting the ends off fretwire. A Stewart-MacDonald exclusive.
Vintage-style Tuner Knobs
20s-style cream knobs and more. Replace deteriorated knobs on vintage instruments.
Vintage-style 3-on-Plate Tuners
Ideal replacement for the many 3-on-plate tuners with plastic knobs.
More More More
Nut and Saddle Vise
A better way to hold nuts and saddles for easier, faster shaping.
StewMac Super Glue
First choice in guitar repair shops! Incredible bonding strength for quick jig-making, fretting, inlaying, finish touch-ups, and more.
Pipettes
Useful in every shop when gluing, finishing and more.
More More More

Toll-free order line:   800-848-2273   9am-6pm Eastern Time, M-F



Your order | Your account | Trade Secrets E-mail Newsletter
Home | Free catalog | Catalog Quick Order | International | Customer service
Our guarantee | Shipping | Security & Privacy | Contact us
Site map | About Us | Employment
© Copyright 2014 Stewart-MacDonald
Your shopping is secure with VeriSign! Trusted Commerce