Stewart-MacDonaldEverything for building and repairing stringed instruments!
Your order cart Your order | Account | Saved list
Sign in
Email
800-848-2273, 9AM-6PM EST, M-F
Home Free catalog Quick order International Customer service

Home : Trade Secrets Archive : Issue 74, eBay mandolin: fret work and using JB Weld to rebuild a truss rod nut
Trade Secrets NEWSLETTER
Email a friend









 Processing...






Is this eBay mandolin a good deal?

Photo: eBay mandolin


Dan Erlewine
You've been outbid.
Bid again before it's too late!


My customer “won” this Fender F-style mandolin on eBay for $200. It retails for $850, so he got a great deal if I can fix it inexpensively. Let’s see what kind of troubles it has...

Dan Erlewine signature Dan Erlewine, November 13, 2008

Photo: mandolin in repair vise


This “eBaby” has problems:

Fret buzz from loose frets

An easy fix, using super glue and car wax.

Fret buzz from a warped neck
Inspecting the mando in the repair vise,
this problem led me to the next one:

Stripped-out truss rod nut
I used JB Weld to fix this one.

Photo: using the FretRocker Animation: FretRocker closeup
Buzzing frets
I used a FretRocker to locate the problem frets. It has four different straightedges to span any group of three frets, so it teeter-totters when it sits on a fret that’s taller than its neighbors. I found that the eleventh and the fourth frets had lifted up out of their slots a little.
Fret Rocker
Photo: super glue
Car wax, then super glue
I swabbed a little silicone-free paste wax on the fretboard beside the loose frets. This keeps glue from sticking to the fretboard, so it chips away easily with a razor blade.

After waxing the board, I put some water-thin #10 super glue under the frets. The glue bottle’s whip-tip puts the glue right where the fret meets the board. Thin, fresh super glue disappears down under the fret, pulled by capillary action. A clamp and a piece of plexiglass hold the frets down for a couple of minutes while the glue sets.
Stew-Mac Super Glues
Photo: straightedge
About that warped neck
Laying a straightedge on the frets showed that the strings were also buzzing against the last few frets up on the fingerboard extension. Hopefully, straightening the neck will make this go away. I’ll have to raise the bridge a little, because when the neck straightens the strings will be lower.
Precision Straightedges

Photo: clamping a mandolin
Guitar Repair Vise Cam Clamp
Here’s how I hold a mando for neck work
A cam clamp grips the peghead, and my repair vise holds the cam clamp.

The two red arrows show where I apply another clamp, using three wooden cauls and a wood crossbar. You can see that clamp in this photo:



This rig gently bends the neck straight. By doing this before adjusting the truss rod, I save that skinny little rod from doing the hard work: it doesn't create the straightness, it just holds it in place.
Mangled truss rod nut
The truss rod’s adjusting nut has been mangled by somebody using a too-small hex wrench. Instead of a clean six-sided hex shape, the opening’s become rounded. And this nut is permanently attached to the rod—it’s not the kind that can be removed and replaced.

Photo: mangled truss rod nut

If this were a 1/8" allen nut, there would be no problem: our Gripper truss rod wrench works with ruined 1/8" nuts. But this one’s too large for the Gripper. Maybe we need a complete set of Gripper wrenches. (Hey, that's a good idea! Watch for news in an upcoming Trade Secrets...)
Gripper Truss Rod Wrench
I degreased the damaged adjusting nut with alcohol and Qtips, then carefully tapped a truss rod wrench into it. I managed to tighten the nut just enough to hold the neck. Experience tells me I was lucky: this stripped nut isn't going to allow any more adjustments.

I decided to do some future repairman a favor by rebuilding the nut using JB Weld from the home supply store. This is a hit-or-miss technique: sometimes it’s worked for me and other times... not so much. It's worth a shot.
Allen Truss Rod Wrenches
Photo: mandolin held vertically

I held the mandolin vertically by mounting the repair vise sideways in a block of wood clamped to my bench.
Photo: mixing JB Weld

I super-cleaned the nut with Qtips and alcohol, then mixed up some JB Weld, a gray epoxy that hardens like metal.
Photo: applying JB Weld

I waxed the Allen wrench, put it in place, and packed JB Weld around it.
Photo: repaired truss rod nut
It worked!
At least I think it did. I'm going to leave it alone rather than test it. The next person to work on this mandolin has a better starting point with this epoxy-supported truss rod nut than I had without it.

All in all, I'd say this eBay auction turned out to be a good deal for my customer. (I didn't charge him for the JB Weld experiment on the truss rod nut.)

Dan Erlewine signature

Problem-solving products mentioned above:
Photo: Fret Rocker Photo: Guitar Repair Vise Photo: Cam Clamps
Fret Rocker
Our new 4-in-1 mini straightedge for pinpointing high frets.
Guitar Repair Vise
The luthier's favorite vise is even easier to use, thanks to custom modifications: bearing-smooth operation, fast crank handwheel, and urethane/hardwood swivel jaws.
Cam Clamps
Cam clamps are a favorite of all types of woodworkers and they come in very handy in lutherie as well. We offer high-quality clamps in two sizes.
Buy Now
Buy Now
Buy Now
Photo: Allen Truss Rod Wrenches Photo: String Action Gauge Photo: Stewart-MacDonald Super Glues
Allen Truss Rod Wrenches
Three special ball-end wrenches for adjusting Allen-head truss rods: 1/8", 4mm, and 5mm.
String Action Gauge
Fast, accurate setup gauge for every stringed instrument.
Stewart-MacDonald Super Glues
The only instant glues formulated specifically for instrument repair! You'll need them for jig-making, nut slot rebuilding, inlaying and more...
Buy Now
Buy Now
Buy Now

Toll-free order line:   800-848-2273   9am-6pm Eastern Time, M-F



Your order | Your account | Trade Secrets E-mail Newsletter
Home | Free catalog | Catalog Quick Order | International | Customer service
Our guarantee | Shipping | Security & Privacy | Contact us
Site map | About Us | Employment
© Copyright 2014 Stewart-MacDonald
Your shopping is secure with VeriSign! Trusted Commerce