Stewart-MacDonaldEverything for building and repairing stringed instruments!
Your order cart Your order | Account | Saved list
Sign in
Email
800-848-2273, 9AM-6PM EST, M-F
Home Free catalog Quick order International Customer service

Home : Trade Secrets Archive : Issue 66, Strengthening a square-tube Martin truss rod
Trade Secrets NEWSLETTER
Email a friend









 Processing...






Square Martin Truss Rod
Easy way to beef up the neck

Strengthening a square-tube Martin truss rod

If you ever reset the neck on a 70s-era Martin, here's a tip you'll like: straightening and stiffening Martin’s hollow tube truss rod with carbon fiber.

Dan Erlewine signature Dan Erlewine, July 24, 2008
Dan Erlewine
Martin T-bar Truss Rod
Before 1967, Martin guitars used a much-loved iron T-bar for neck reinforcement. In ’67 they switched to a hollow steel tube, 3/8" square. These tubes weren’t as stiff as the T-bar, so many Martins of this era have a somewhat “spongy” neck that pulls into an up-bow and stays there. In 1985 they introduced the adjustable truss rod that they use today.

When I’m resetting the neck on one of these hollow-tube Martins, I take advantage of having the neck off by gluing a carbon reinforcing rod inside the hollow tube. A lightweight superstiff material, carbon keeps the neck straight, and adds a significant improvement in tone. Here’s how to do it:



Neck Removal Jig
Neck Removal Jig
Removing the neck
Remove the neck. Nothing beats the neck that steams out clean and easy, letting the neck removal jig do its thing. This neck joint came apart without a problem.

Open end of truss rod
There’s the hollow tube, 3/8" square with a 1/4" hole in the middle. Clean away any glue that blocks the opening.

Martin Style Truss Rod
Martin Style Replacement Truss Rod
Checking neck straightness
With the strings off, this neck has relaxed into a dead-straight configuration (measured with a notched straightedge).

Notched Straightedge
Notched Straightedge
Using the Neck Relief Gauge

Carbon fiber with a binding filler
The neck relief gauge tells me the same thing: the neck is straight. I’m clamping it up to make sure the truss rod stays straight for accepting the carbon rod: a cam clamp in the repair vise holds the peghead while a block of wood supports the heel.

Doing a dry run:
Our 1/4" x .200" carbon fiber rod slides easily into the tube. There’s a little gap beside this rectangular rod in the square tube. Here I’m doing a test-fitting a strip of .020" plastic binding, which creates a snug fit. (A thin strip of hardwood would also be a good choice of shim material.) Now that I know the pieces fit, I'll pull them out and set up for gluing.

Neck Relief Gauge
Neck Relief Gauge



Carbon Fiber Neck Rod
Carbon Fiber Neck Rod
Clamping the neck straight
The neck needs to be straight for the inserts to slip in, so I’m clamping it to a stiff bar (a carpenter’s level) to hold it straight. A mini cam clamp is doing the job.

Mini Cam Clamp
Mini Cam Clamp


Which truss rod do we use in our Dreadnought Guitar Kit?
The Stewart-MacDonald Dreadnought Kit is built to a plan drawn by Don MacRostie. (We include the plan for free with the kit.) Don specified the two-way adjustable Hot Rod Truss Rod for this kit, so the guitar you build will have a fully adjustable neck. Learn more about this kit:

Clamp the neck vertically

Pushing the epoxy in
Hold this setup vertically in the repair vise, and warm up the neck using desk lamps. The heat will help the glue run down into the hollow tube quickly and evenly. Watch out for the heat from those lamps! Don't get too close, and move the lamps every minute or so.

Mix enough slow setting epoxy to fill about 1/3 of a mixing cup.

Pouring the epoxy

Pour about half the glue into the tube. Protect the neck by taping it off as you see here. (Hot hide glue would also work well for this if you can work fast enough before it cools.)

In the photo at left, I'm using an old round truss rod as a ramrod to be sure the glue gets where it needs to.

Guitar Repair Vise
Guitar Repair Vise






Mixing Cups
Mixing Cups



Stewart-MacDonald Epoxies
Stewart-MacDonald Epoxies

Slide the carbon fiber and binding in together — brushing glue between them as you push them into the hole.

After removing the masking tape, I cleaned up the glue overspill with Behkol solvent. The carbon-stiffened neck needs to dry overnight.

Glue Brushes
Glue Brushes



Behlen Behkol Solvent
Behlen Behkol Solvent
Cleaned up with Behkol solvent


On with the job!

Dan Erlewine signature

Problem-solving products mentioned above:
Photo: Carbon Fiber Neck Rods Photo: Neck Removal Jig Photo: Neck Relief Gauge
Carbon Fiber Neck Rods
We offer a variety of carbon fiber reinforcement materials for use in your instruments.
Neck Removal Jig
For faster, cleaner dovetail neck joint disassembly.
Neck Relief Gauge
Takes the guesswork out of guitar truss rod adjustment, for more consistent and accurate playability.
Buy Now
Buy Now
Buy Now
Photo: Notched Straightedge Photo: Black Plastic Binding Photo: Stewart-MacDonald Epoxies
Notched Straightedge
Check the straightness of the fingerboard with the frets in place!
Black Plastic Binding
65" long to reach around entire guitar! Variety of dimensions.
Stewart-MacDonald Epoxies
High quality clear and black epoxies.
Buy Now
Buy Now
Buy Now

Toll-free order line:   800-848-2273   9am-6pm Eastern Time, M-F



Your order | Your account | Trade Secrets E-mail Newsletter
Home | Free catalog | Catalog Quick Order | International | Customer service
Our guarantee | Shipping | Security & Privacy | Contact us
Site map | About Us | Employment
© Copyright 2014 Stewart-MacDonald
Your shopping is secure with VeriSign! Trusted Commerce