Stewart-MacDonaldEverything for building and repairing stringed instruments!
Your order cart Your order | Account | Saved list
Sign in
Email
800-848-2273, 9AM-6PM EST, M-F
Home Free catalog Quick order International Customer service

Home : Trade Secrets Archive : Issue 54, How to spray a sunburst using aerosol cans
Trade Secrets NEWSLETTER
Email a friend









 Processing...






Two strat bodies, sunbursted with spray cans

How to spray a sunburst using aerosol cans

Customers ask me, “Can I really get a good ’burst with spray cans?” The answer is “Yes indeed!” I sprayed these Strat bodies in my shop last week, and took some pictures to show you how...

Erick Coleman signature Erick Coleman, February 7, 2008
Photo: Erick Coleman
Here’s how I spray sunbursts without a spray gun

Test-sprays on scrap wood
If you've got some finishing experience under your belt, this will be a piece of cake. But if this is your first time finishing, start by practicing on scrap wood like I did. You’ll get the hang of it quick. (Here’s my pile of scrap covered with test-bursts.)

Start with a guitar body that’s been prepped for finishing: grain-filled if necessary, sanded to 320 grit and sprayed with 2-3 coats of clear sanding sealer.

Sunburst Step 1: Black on the outside edge

Masked body, ready to spray
I wanted to blacken the sides without getting overspray on the front or back, so I used a brown paper mask. A few very small pieces of double-stick tape held the kraft paper in place, with the edges loose so they didn’t interfere with a nice feathering to the edge of the black spray.
Unfinished Strat Body
Strat body

Unfinished Tele Body
Tele body


ColorTone Black Aerosol Lacquer
ColorTone Black Aerosol Lacquer
Spraying the black edge
With the guitar face-up on your workbench or in a homemade stand, begin spraying the outside edge. Point the nozzle at a 45 degree angle down at the top, coming in from the edges with the nozzle of your spray can set for a horizontal pattern. Make light passes all around the top edge, then flip the body over and do the same on the back. You want a nice black band around the outside edge. Avoid spraying directly into the gap between the mask and the body, which would put black where you don’t want it.

Black edge sprayed
Once the black dries, remove the mask and clean up any unwanted overspray with 320 grit paper. Be sure to clean up any sanding dust before proceeding.
3M Gold Fre-Cut Sandpaper
3M Gold Fre-Cut Sandpaper
Sunburst Step 2: Vintage amber on the front and back
Vintage Amber on front and back
Now we apply the vintage amber coats, followed by a couple of clear coats. Let the guitar dry.
ColorTone Tinted Aerosol Lacquer
ColorTone Tinted Aerosol Lacquer
Guitar Finishing book Rig up a simple holder to make spraying easier: see pages 39 - 40 of our Guitar Finishing Step-by-Step book for ways to hold bodies and necks while you spray.

Body/neck holder ideas

Sunburst Step 3: Tobacco brown blends the black and amber
Spraying at a 45-degree angle

3-color sunburst illustration
With the guitar still face-up, it's time to add tobacco brown to the outer edge. Spray from the inside out, with the can at a 45 degree angle. Keep half or more of the spray pattern off the body, gradually bringing the spray inward until you’ve got the blend you’re after. Use multiple passes to get a dark outer edge fading into a nice reddish transition from the brown overspray on the amber. To prevent runs, spray only a couple of coats and let it dry for a few minutes before continuing.

Keep in mind that the further you hold the can from the body, the wider the spray is going to be.

This step is a good time to run some tests on scrap wood.
The secret is patience: don’t lay down too much color too fast!
That would cause runs and a badly shaped spray line.
Removing overspray speckles
Clean up the overspray
After the color is dry, look for unwanted overspray in the amber area. Since you sealed in the amber with a couple of coats of clear, you can very lightly sand away any brown speckles using 400 grit sandpaper without sanding through to the color. Again, clean away the sanding dust.
Finishing Papers Sampler
Sampler of Finishing Papers
Tips for using aerosols:
Warm the spraycans in water
Use warm cans, not cold.
Cold aerosols will spit and spatter, so heat your cans to 75 or 80 degrees F. by setting them in a pan of warm tap water. This does the trick.
ColorTone Clear Aerosol Lacquer
ColorTone Clear Aerosol Lacquer
Keep your finger out of the spray!
Use multiple cans!
Keep one can warming while the other’s spraying. When one can becomes cold to the touch, swap it for the cozy warm one. And if a nozzle becomes obstructed by built-up lacquer, pop it off and drop it in lacquer thinner while the other nozzle takes a turn.
Behlen Nitrocellulose Lacquer Thinner
Behlen Lacquer Thinner
Keep your finger out of the spray!
Keep out of the spray!
Make sure your fingertip is on the back of the button, where it won’t get into the finish. Otherwise you'll have a mess on your hands.
Erick Coleman with sunbursted Strat
With the body ’bursted and cleaned up, apply 4-10 clear coats. Then buff it to finish off the job!


Erick Coleman signature
Finesse Polishing Pad
Finesse Polishing Pad

Problem-solving products mentioned above:
Photo: ColorTone Aerosol Guitar Lacquer Photo: Sandpaper / Finishing Paper Sampler Photo: ColorTone Essential Finishing Kit
ColorTone Tinted Aerosol Guitar Lacquer
The easiest way to spray a professional finish!
Sandpaper / Finishing Paper Sampler
See what a difference precision abrasives can make!
ColorTone Essential Finishing Kit
Our complete finishing kit dedicated to keeping it simple. FREE finishing book included!
Buy Now
Buy Now
Buy Now
Photo: ColorTone Aerosol Guitar Lacquer Photo: Finesse Polishing Pad Photo: Double-stick Tape
Colortone Waterbase Grain Filler can be used under waterbase or nitrocellulose finishes, and it's ideal for open-grained woods such as mahogany, walnut, ash, koa and rosewood.
Finesse Polishing Pad
Low cost buffing pads for your drill that will give you professional results.
Double-stick Tape
For holding router templates, attaching acoustic guitar pickguards, and lots more.
Buy Now
Buy Now
Buy Now

Toll-free order line:   800-848-2273   9am-6pm Eastern Time, M-F



Your order | Your account | Trade Secrets E-mail Newsletter
Home | Free catalog | Catalog Quick Order | International | Customer service
Our guarantee | Shipping | Security & Privacy | Contact us
Site map | About Us | Employment
© Copyright 2014 Stewart-MacDonald
Your shopping is secure with VeriSign! Trusted Commerce