Stewart-MacDonaldEverything for building and repairing stringed instruments!
Your order cart Your order | Account | Saved list
Sign in
Email
800-848-2273, 9AM-6PM EST, M-F
Home Free catalog Quick order International Customer service

Home : Trade Secrets Archive : Issue 49, Binding and fretting a Red Diamond mandolin fingerboard
Trade Secrets NEWSLETTER
Email a friend









 Processing...






Photo: Red Diamond mandolin

Fretting a bound mandolin fingerboard

Here’s my two-step technique for fingerboard binding and fretting on my Red Diamond mandolins.


Don MacRostie signature Don MacRostie, November 29, 2007
Photo: Don MacRostie
The frets go in before the neck goes on
I fret the fingerboard before gluing it to the neck. This is a flexible way to work, and gives clean results even with multiple bindings and overhanging frets like the example I’ll show you here.

Photo: shaping the fingerboard
First step: the binding
Starting with a pre-slotted fingerboard, I rout it with our ball bearing router bit to the shape of the board minus the thickness of the binding. I use a router table, following an acrylic pattern fastened to the fingerboard with double-stick tape.
Photo: binding the fingerboard
After shaping the board, I bind it with single white binding. The binding is a little taller than the board itself; I sand away the extra height after the glue has dried for a few hours.

White plastic binding
Photo: cleaning the fret slots
I use our fret slot cleaning tool to pull the nearly hardened binding glue from the fret slots. (Don’t wait too long or this job becomes unnecessarily difficult!)

Fret Slot Cleaning Tool
Photo: sanding the fingerboard
Install position dots and sand them flush with the surface.
Photo: routing for the trim
Here comes the good part: multiple bindings
I rout the bottom edge of the fingerboard, binding and all, creating a recessed ledge for adding trim at the bottom of the main binding. Adjust the router bit to accommodate the binding plus a small allowance for glue.

Here I’m using a .020 white and .020 black trim under the solid white edge binding. (I laminate them with our binding laminator.)

Mandolin Fingerboard, slotted
Photo: installing side dots
When the glue has set, smooth the two bindings so they’re flush to each other. Install the side dots, clean everything up, and you’re ready to install the frets!

Side Dot Material
Photo: Les Paul clone
For Red Diamond vintage models, I choose Waverly mandolin machines in silver. I use the longer post spacing (1920s Loar style). The antique silver and vintage engraving feel exactly right.
– Don
Photo: FretBender
Second step: the frets
I bend the fretwire with the FretBender to give it a radius before cutting the frets to length. I’m using a radiused fingerboard, and I overbend the wire just a bit. This encourages the fret ends to stay down.

FretBender
Photo: Fret Arbor Press

Photo: Fret Arbor Press
I use our fret arbor press with a special cradle I made for holding the mandolin fingerboard.

I’ve modified several fretting tools for mandolin use. This holding fixture has holes drilled through it at each fret position. The holes drop onto a register pin, quickly and accurately aligning each fret slot under the arbor press. I don’t even have to think about it; the fret caul lands right over the fret slot. One less thing to worry about.

Fret Press System
Photo: Fret Arbor Press

Photo: Fret Arbor Press

Photo: Fret Arbor Press
Okay, let's install some frets
I start by clipping back the tang under one end of the fretwire using the Fret Tang Nipper. This creates the overhang needed for the crown of the fret to sit on top of the edge binding.

With a pen I mark where to nip the tang on the other side, deducting 1/32” to allow for board shrinkage. This eliminates those annoying little bumps where the fret ends try to push the binding away from the fretboard.

Fret Tang Nipper
Photo: Fret Arbor Press
I press the fret in, then clip the excess wire flush to the binding. This leaves the overhanging fret crown ready for installing the next fret. It’s fast and efficient.
Photo: Fret Press Caul
Photo: Fret Press Caul
Two tools I modify for mandolin work: With a hacksaw I cut the ends off the fret press caul so it’s mando-width instead of guitar-width.

To adapt the Fret Tang Nipper for mando fretwire, I use my belt sander to carefully grind .017" –.020" from the top surface of the tool’s cutting anvil. (This can be accessed by removing the nut, spring and hold-down from the end of the tool, then taking out the Phillips screw that holds the cutting anvil.

Fret Press Caul
Photo: Fret Arbor Press

Photo: Fret Arbor Press
Trim and file the fret ends with a fret end dressing file for a comfortable feel.

The fingerboard’s ready to be installed except for one last thing: it needs a massage!

The fret tang barbs pressed into the slots cause the board to back-bow into a curve. To flatten it for gluing, massage the board by lifting one end, gently bending it in the opposite curve. This presses the barbs into the fret slot walls, and the board will lay quite flat. Now you’re ready to install your completely fretted board!

Don MacRostie signature

Fret End Dressing File

Problem-solving products mentioned above:
Photo: Mandolin Fingerboards Photo: Binding Router Bit Photo: White Plastic Binding
Mandolin Fingerboards
Pre-slotted fingerboards available in standard flat playing surface or with a 12" radius.
Ball Bearing Router Bits
Extra-long carbide tipped router bits for control cavity, pickup and other solidbody routing tasks.
White Plastic Binding
65" long to reach around an entire guitar! Variety of dimensions.
Buy Now
Buy Now
Buy Now
Photo: Black Plastic Binding Photo: Fret Press System Photo: Binding Router Bit Set
FretBender
The quickest way to properly pre-bend fretwire and prepare it for installation.
Fret Press System
Complete with self-leveling caul, hardwood neck support, and five radiused brass inserts.
Binding Router Bit Set
Cuts eight standard binding channels on your instrument, and fits your full-size router.
Buy Now
Buy Now
Buy Now

Toll-free order line:   800-848-2273   9am-6pm Eastern Time, M-F



Your order | Your account | Trade Secrets E-mail Newsletter
Home | Free catalog | Catalog Quick Order | International | Customer service
Our guarantee | Shipping | Security & Privacy | Contact us
Site map | About Us | Employment
© Copyright 2014 Stewart-MacDonald
Your shopping is secure with VeriSign! Trusted Commerce