Easy, affordable way to make your own custom-fit guitar case For the few most-common guitar shapes, it’s no problem to find a hardshell case. But what about all those guitars that are too big, too small, or just plain odd? Todd Sams, April 2, 2009

			How do you protect an odd-shaped instrument? This old cardboard guitar case is a goner. It’s so warped, the case itself is liable to hurt the guitar when it’s lifted it in or out. And it’s a bad fit, so the guitar rattles around inside. It never provided good protection, even when it was new. The guitar is a 1939 Gibson L-00, with a small body that doesn’t fit most ready-made cases. And the owner doesn’t want to shell out big bucks for a custom case.
		I found a simple solution: modify a LiteCase. LiteCases are built on an expanded-foam frame that’s easy to carve. Unfasten the tough nylon outer skin and you have access to the frame, which you can easily enlarge, reduce, or reshape. This works like a charm for making an affordable custom-shaped case.
		Here’s a larger guitar that I made a custom-fitted case for.
		Here’s an old Epiphone archtop that’s too big to fit down into a dreadnought-size LiteCase. Laying the guitar on the open case shows that there’s enough room to fit the guitar, if the Styrofoam core is reshaped.
		To get at the foam, I used our guitar tech’s screwdriver set to remove the Phillips screws around the lower half of the case. This let me pull the outer covering down, exposing the edges of the inner plush lining. The plush is fastened to the core with contact cement, and it can be pulled away.						Guitar Tech Screwdriver Set
Ordinary polish leaves residue that causes nothing but trouble for repair shops. Preservation Polish delivers shine, not slime!
		With the plush liner pulled back, I trace the guitar’s shape onto the foam to show where material needs to be removed. With a sharp seam separation knife, I cut out my shape. The waist of this archtop is tighter than a dreadnought, so getting a custom fit there means adding material to the foam. I used a sheet of urethane foam from the craft department at WalMart. They also carry a spray adhesive that works well with this.						Seam Separation Knife
		I cut it into strips the height of the case wall. It trims easily. After test-fitting, I applied spray adhesive and put my patches onto the foam framework. Binding tape holds these in place until the glue dries.						Binding Tape
Putting the case back together is simple: the plush lining still has the tacky contact cement, and sticks right back in place. If a spot feels loose, a little of the spray adhesive will fix it. Smooth out any wrinkles and pull the edges back over the top of the Styrofoam. Pull the outer cover back into place, and zip the case shut. Now you can put the screws and washers back into the same small holes they came from. When I was all done, I left the case open long enough for the spray adhesive to dry thoroughly, so any vapors had plenty of time to dissipate before I zipped the guitar inside.
		Making a custom case for a small guitar
		It’s even easier to modify a case for a smaller instrument like the L-00. Starting with a 000-size case, I pull back the fabric and add urethane foam until I get a good fit. This picture with the black fabric still in place gives a good idea of how much foam I needed to add.
		Fitting even more unusual shapes I’ve also modified LiteCases to fit other guitars. (A 12-fret Maccaferri type Gypsy jazz guitar fits very nicely in a 12-fret 000-size case.)
		Dreadnought-size LiteCase: Upper body bout: 12" wide Lower body bout: 15-3/4" wide 000-size LiteCase: Upper body bout: 12" wide Lower body bout: 15-1/4" wide Electric Guitar LiteCase: Cavity is 13" wide x 18-3/4" long
		As long as the instrument is smaller than the case, your search for that impossible-to-find case is over!

	Problem-solving products for this kind of work:

	Binding Tape Super strong and super useful in the shop.		Guitar Tech Screwdriver Set Our versatile 19-in-1 set especially for fretted instrument hardware. A Stewart-MacDonald exclusive.		Seam Separation Knife The ideal knife for removing tops, backs and fingerboards from most instruments.

To reply to this email, please use this web page: stewmac.com/email Our customer service representatives are available to serve you 9am-6pm weekdays EST. Call 800-848-2273 today. Stewart-MacDonald - Everything for building and repairing stringed instruments! © 2013 Stewart-MacDonald, 21 N. Shafer Street, Box 900, Athens, Ohio 45701 Toll-free: 800-848-2273Website: www.stewmac.comE-mail: www.stewmac.com/email You are receiving this e-mail because you have a stewmac.com Trade Secrets subscription. If you wish to unsubscribe or change your e-mail address, please click here.