 |
 |
 |
|
 |
|
 |
|
 |
|
 |
|
 |
|
 |
 |
|
||||||||
|
|
|
|
|||||
 |
|
I modified this drill bit to install fingerboard dots that line up on center Drilling holes for side dots on a fretboard isn’t easy with ordinary twist drills because twist drills seem to enjoy wandering off center! I can’t deliver a customer’s guitar with the dots staggering around the edge of the fingerboard, so I solved this problem in my shop by grinding a tiny brad point onto a 3/32" twist bit. Here’s how to do it.
|
|
 |
||||
 |
||||||||
 |
||||||||
| Making my own brad-point bit |
 I found this nifty anvil-base depth micrometer in a box of tools, and used it for years to measure fret height. My repairman pal Frank Ford offered a better solution, and Don MacRostie made it happen: a luthier-friendly caliper that straddles the fret and gives a digital readout.   The modified jaw fits over the fret tang to measure fretwire crown height, too. This custom caliper is the one we now carry at stewmac.com  |
|||||
 |
Here's an enlargement of my homemade brad point bit vs. the standard twist drill it was before I modified it. You can see how the brad point is going to stay on center, creating a nice flat-bottomed hole. |
|||||
 |
Step 1 Put a small grinding wheel into your Dremel tool, and mount it in the precision router base. Clamp this into a small vise. I'm using my nut and saddle vise — it's a heavy little thing, and it makes a good "third hand" with a solid grip. |
|||||
 |
Clamp that rig to your benchtop and you have a small Dremel "grinder" with a working table. |
|||||
 |
Step 2 Clamp a small square item to the router base to use as a fence, centering it with the router bit. The drill bit will ride against this fence. (I used the square corner of our steel Fret Rocker for this.) The blue marker ink on the drill bit will make it easy to see where the grinder's removing metal. |
|||||
 |
This turned out to be a handy trick: I clamped a 1" repair magnet to the underside of the aluminum router table — the force of the magnet keeps the drill bit hugging the table and fence. |
|||||
 |
Step 3 Grind each cutting edge flat, stopping before reaching the center — leave that brad point! |
|||||
 |
On the face of the wheel, grind a little back angle leading up to the cutting edge of the lip. Dress the new edges by hand with a sharp file (I used my diamond nut file). |
|||||
 |
The sharpened tip will keep the bit centered, and the new bit will drill a clean, sharp-edged hole. Just the right size for a white side dot. |
|||||
 |
||||||
 |
|
How not to measure a drill bit Did you know the way to measure a drill’s diameter is not by putting a caliper on the shank? (I learned this from hanging around machinist-types.) Instead, measure the cutting tip from point to point; that’s what makes the hole, and it’ll be wider than the shank. |
||||
|
|
|
Problem-solving products mentioned above: |
|
 |
|
 |
|
 |
|
|||||||||
|
|
|
|
|
|
|
|||||||||
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|||||||||
|
|||||||||||||||
|
 |
|
 |
|
 |
|
|||||||||
|
|
|
|
|
|
|
|||||||||
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|||||||||
|
|||||||||||||||
|
To reply to this email, please use this web page: stewmac.com/email Our customer service representatives are available to serve you 9am-6pm weekdays EST. Call 800-848-2273 today.  Stewart-MacDonald - Everything for building and repairing stringed instruments! © 2006 Stewart-MacDonald, 21 N. Shafer Street, Box 900, Athens, Ohio 45701 Toll-free: 800-848-2273 Website: www.stewmac.comE-mail: www.stewmac.com/emailYou are receiving this e-mail because you have a stewmac.com Trade Secrets subscription. If you wish to unsubscribe or change your e-mail address, please click here. |
