Ratings and reviews

Read the directions, prepare your guitar the way it says and your guitar will look as good as new if not better. And it is so easy. I will be using it again and again....Thanks StewMac...

This product is amazing, If you can read and follow directions you can make you guitar look great. I will be using these products again and again...Thanks

I used this template to install two dual-battery boxes into two different guitars. It worked fine, and the battery boxes fit well.

This is good tape in that it does what tape should do: it sticks. I used it to attach router templates, and the templates did not slip.

This is a nice box. I purchased it with the plexi template, so routing and installation was extremely easy. It can be a bear to open, but as I only change batteries every few months, it's not that big of a deal to me.

I used this kind of truss rods in many necks. 10 000 times better than original fender rods, adjusting is piece of cake. Installing even easier. If they are installed properly. Make sure that you read the instructions. At least there are few tips and tricks to ensure proper work and satisfaction !

Worked for a week or so; (non daily use) I may have been using it too harshly, because it blunted out and was useless after about a week. I was only using a small hammer to set the eyelets just to be to be extra careful. (The eyelets don't need much umph to bevel properly)

The material it was made out of seemed very cheap in my opinion.

Going to order a new one today, to see if they are any better now. This has been about six months since my last one died.

I'd rather pay 4 x's as much for one that is solid steel, or iron as long as it will last.

Perfectly planed blank, size is optimal for stratocaser's or similar neck type. Or better to say 25.5" sized scales.
Just like said, ready to go under you band saw and ready to be enjoyed in it !

Perfect drop in replacements for the stock Grovers on my Epiphone Sheraton! Now it stays in tune!

I installed a set of Golden Age Parsons St HBs to upgrade an import Hamer guitar I bought for a backup. Now my backup is my No. 1, replacing a Japanese Yamaha LP style w/Duncan Seth Lover pups (no slouches in the tone dept, either)! The pots are stock 500K with an Orange Drop .022 tone Cap. The best part is that the Hamer with these pups sounds great with all my gear including L6 M13, Boss GT-10, Fender SS 22 and Peavey Windsor Studio amp.

The tone is very balanced, not Bass or Treble heavy, with just enough output to stay very clean during chording. I may get a pair to replace my Seths in the Yamaha, no kidding!

I was thinking how to manage planing of my bound fretboard to an even radius without having to remove the white fretboard edging, and still be able to restore the fretwire-slots to correct depth. I was advised to check this tool out and it was the perfect tool for the job.

I recently received my 16" block and just finalized my first fretboard planing. Perfect result. One very satisfied customer.

Perfect glue for all kinds of jobs. Use them often with the whip tips (item no 1161)

Bought the nickel version ,fitted perfectly with the Kluson tuners.

Use it for nuts. Some people make it themselves but I use it not so often. This container will last at least a year

Plays like butter!

Excellent bushings , fits perfectly.
Got them in without using force , still a tight fit.

Nice saddles with a very large 'stringhole'. Strings do not touch the saddle otherwise than on top of the saddle, very important!

Used it to repair an SG.
Wood itself was great but the slots were way too deep. I liked to use the whole thickness of the fingerboard , now I had to use a plainer to get the slot as deep as the fret tang would go.
At StewMac they suggested I filled the spaces with super glue ,I think that's not the way it should be.
Next time I will buy the unslotted version

Fits a small 'shaft' switch perfectly.

Used it on an old Symphonie guitar.
Sanded the bottom flat to fit the guitar so it became smaller ,sanded also the top unit flat so the adjustable thumbscrews weren't needed anymore.
There was a piece of paper under the bone saddle, I took that off

Used them on an old Symphonie guitar.
Works and looks good!

Very nice tool, I had previously tried to make my own from a standard end cutter, but none of my attempts would cut as great as this does. Makes a nice, square cut and up close too!

Worked perfectly, hard to imagine trying to get a perfect radius without it.

This is a great quality item and is very useful having threaded fitting so to let you fit a screw for use with single co-ordinator rod. I wish i could get matching Brackets to go with it