| DEPARTMENTS |
|
| Accessories |
|
| Bindings,
trim |
|
| Bodies,
necks, wood |
|
| Books,
plans |
|
| Bridges,
tailpieces |
|
| Electronics,
pickups |
|
| Finishing
supplies |
|
| Fretting
supplies |
|
| Glues,
adhesives |
|
| Hardware,
parts |
|
| Inlay,
pearl |
|
| Kits |
|
| Knobs |
|
| Nuts,
saddles |
|
| Pickguards |
|
| Tools |
|
| Truss
rods |
|
| Tuners |
|
| Video, DVD |
|
|
|
|
ColorTone Waterbase Sanding Sealer
Directions for use
|
i-5573 Updated 11/06
Safety
Use in well ventilated area. Avoid inhaling spray. Prolonged exposure may cause headaches and mucous membrane irritation. Wear a NIOSHA-approved respirator while spraying. Direct contact with skin or eyes will cause extensive irritation. Wear safety glasses, rubber gloves and protective clothes.
Preparation
Mix well. Stir gently, do not shake. Allow air bubbles to settle before straining and pouring into spray equipment.
ColorTone waterbase products require a clean, dust-free, wax-free surface for optimum performance. New wood should be sanded to 220-grit, vacuumed and blown dust free. If the surface has been contaminated with oils or waxes, wipe down with an equal mix of denatured alcohol and water. If the surface has been modified, clean and test waterbase products compatibility before proceeding.
Application
Waterbase finish doesn't look wet and glossy as you're spraying, unlike nitrocellulose lacquer. Be careful not to lay it on too thick, looking for that glossy wetness. Good lighting is very important. Spray light coats, carefully overlap your spray pattern by 1/3-1/2 for coverage with uniform thickness.
Optimum spraying condition is 70°F, and 45-60% relative humidity. Dry, oil and dirt-free air with proper ventilation is a must.
• For gravity feed gun, 40-60 psi with a tip size of 1.3mm is recommended.
• For siphon feed gun, tip size of 1.8mm is recommended.
Waterbase Retarder or water can be added to reduce viscosity. When hot/dry conditions cause the finish to dry too fast, thin with 5%-15% Waterbase Retarder.
Clean up
Clean spray equipment with warm, clean water immediately after each use. Do not leave lacquer in the spray gun for more than a few hours at a time. Remove dried finish with very hot water and alkaline cleaner (all purpose cleaners, degreasers and strippers). Store unused lacquer in a sealed container and clean gun between uses.
Keep out of the reach of children.
Keep from freezing.
EMERGENCY FIRST-AID PROCEDURES
INGESTION Induce vomiting. Administer large amounts of milk. Seek medical attention.
EYES Flush with fresh water for 15 minutes. Seek medical attention.
SKIN Promptly wash with soap and water, and rinse thoroughly.
INHALATION Remove exposed person to well ventilated area. Seek medical attention if symptoms persist. USE IN WELL VENTILATED AREA. AVOID INHALING SPRAY.
COMPOSITION INGREDIENTS:
| Compound
Name |
CAS# |
| Urethane Copolymer
Resin |
Proprietary |
| Dipropylene Glycol Monomethyl Ether |
34590-94-8 |
| Propylene Glycol Monomethyl Ether |
10217-34-2 |
| Water |
7732-18-5 |
| VOC
Content: 180 Grams Per Liter/0.45 Pounds Per Gallon |
| HAPS
Content: 0.0 |
|
|
ColorTone Waterbase Guitar Lacquers
|
|
|
|
|
