Stewart-MacDonaldEverything for building and repairing stringed instruments!
Your order cart Your order | Account | Saved list
Sign in
Email
800-848-2273, 9AM-6PM EST, M-F
Home Free catalog Quick order International Customer service

Home : Free Information : Electronics : Pickup building : P-90 Pickup Kit with Vintage-style Bobbin

P-90 Pickup Kit with Vintage-style Bobbin

Assembly instructions



Email a friend

i-5980 Updated 03/12









 Processing...







Gibson's R&D team designed the P-90 in 1946 and it was the most common pickup used on the company's guitars until the PAF started appearing on production instruments in the late 50s.

The P-90 pickup is a punchy single coil with a fat, warm sound and a great high end response that is still used by Gibson on a number of models to this day.






RECOMMENDED TOOLS, SUPPLIES, RESOURCES

These tools and supplies are recommended to assemble your kit. Where applicable, item numbers for ordering from Stewart-MacDonald are included.
Soldering iron
42-AWG pickup coil wire
Pickup winder: Schatten Pickup Winder
Pickup coil tape
Volt/ohm meter: Portable Digital Multimeter
Magnet Polarity Tester

StewMac has lots of free technical literature online at stewmac.com/freeinfo. One instruction in particular, Pickup Winding with the Schatten Pickup Winder, has helpful tips on troubleshooting, technique, potting, remagnetizing a pickup, and pickup specifications. A great reference for building any type of pickup!



PREPARATION

Carefully inspect the bobbin to make sure there are no rough edges, nicks, or molding lines that may snag the coil wire. Smooth any possible snags with 600-grit sandpaper or a fine emery board.

Original P-90s used black hookup wires for the starts and finishes, but that can get confusing when attaching the lead wires. We recommend using black for the start, and red for the finish wrap of pickup. Strip back 3/16" off of each end of the hookup wires.

Wrap the end of your 42-AWG coil wire around the exposed end of the black hookup wire. Solder the coil wire to the hookup wire-the heat of the solder should melt the poly-coating off of the copper for a good solder joint. Tape the solder joint off with a small piece of paper coil tape to give it a little extra insulation. Poke approximately 1" of the black hookup wire through the round hole on the bottom of the bobbin-from the inside of the bobbin out through the bottom. Kink the black wire so that it lays flat against the bobbin wall.



WINDING THE COIL


Gibson wound their humbuckers on machines, which means the traverse and layers of the windings are very consistent. You can experiment with winding very methodically to replicate "machine-wound", or "scatter-wind" your coils. The number of turns will affect the pickup's tone and response. More wraps will give you higher output, and more midrange punch. Fewer wraps will give you a more open sound with greater high-end clarity, but less output.
Attach the bobbin to your winder. Traditionally P-90 coils were wound counterclockwise (when viewed from the top of the pickup) with 10,000 turns of wire. Set the "traverse limiter" on your winder so the coil wire stops about .020" from the flatwork on both sides. This helps prevent the windings from deforming and gives a more uniform looking coil. If you have a winder with a counter, set it to zero.

Start the first 6-10 wraps turning the winder by hand to seat the black lead wire and insure that the coil wire won't be pulled off of the bobbin when you start the winding.

Though not a traditional feature on the P-90, many players prefer to have one pickup wound with reverse wind/reverse polarity to allow for hum canceling when two single coil pickups are combined. On a P-90, wind both pickups counter clockwise but connect the braided shield lead wire on one pickup opposite of the other and attach the magnets with opposing polarity.

Once you've achieved the desired number of windings, carefully cut the coil wire and solder it to the red lead wire so it extends about 1" the out of the finish wrap hole on the same end of the bobbin as the start "black" lead wire. Wrap the coil several times with 1/4" wide pickup tape to secure the lead wire and protect the coil wire.



ASSEMBLY

At this stage install the polepiece screws in the bobbin so they stick out of the bottom about 1/8".

When inspecting the nickel silver baseplate you will notice that the holes are slightly rounded on one side and flat on the other. With the flat side down solder black start hookup wire and the outer braided shield of the lead wire to the baseplate and feed it through the hole in the baseplate.



Connect the red finish wire to the inner black "hot" of the lead wire and insulate the joint with paper coil tape or heat shrink tubing.

Install the metal spacer with the rounded side down then install the magnets for South orientation at the polepieces.



Then carefully align and attach the baseplate to the bottom the pickup and tighten the polepiece screws the rest of the way down. Carefully tuck the lead wires in the space between the baseplate and the bottom of the bobbin.





TESTING THE DC RESISTANCE

Test with a volt/ohm meter set to the 20K range. P-90 pickups traditionally read in the low 8K range. If you get an open circuit: are your connections to the coil wire good? Did you solder a break inside the coil which is now causing a short?



POTTING

Potting a pickup (dipping it in melted wax or other material) is a technique used to help eliminate unwanted microphonics. Some pickups, including vintage P-90s, were not potted from the factory. While it's not necessary, potting is generally a good idea. Wax is a traditional pickup potting material that works for most pickups, it's non-toxic, easy to deal with, cheap, and you can undo it if something goes wrong.

Danger: If the wax is too hot you can warp or melt plastic bobbins. If the wax is way too hot you have a potential fire on your hands! Make sure that the wax never smokes-that's an indicator that it's getting too hot. Never try heating your wax on the kitchen stove or in a microwave oven because hot paraffin, and especially paraffin vapors, can ignite. It's best to wax pot outdoors until you have your methods refined and have eliminated any fire hazards.

Stewart-MacDonald's Hot Glue Pot has a thermostat designed to heat hide glue to about 145°. Keep the pot at least 2/3 or 3/4 full. It can operate with less liquid, but the wax may get too hot.

Application: After a pickup has been wound, and the output wires are attached and assembled, suspend the pickup in canning paraffin mixed with 20% beeswax, heated to 145-150° Fahrenheit. After ten or fifteen minutes all of the bubbles should have risen out of the pickup, and all of the voids within the pickup should be filled with a coating of wax.

Pull the pickup out of the wax and suspend it over the wax pot letting the excess wax drip back into the pot. Then lay the pickup on a paper towel and allow it to cool to touch. Carefully remove any excess with a paper towel before the pickup completely cools to room temperature.







P-90 Pickup Kits with Plastic Bobbin
P-90 Pickup Kits with Plastic Bobbin


Toll-free order line:   800-848-2273   9am-6pm Eastern Time, M-F



Your order | Your account | Trade Secrets E-mail Newsletter
Home | Free catalog | Catalog Quick Order | International | Customer service
Our guarantee | Shipping | Security & Privacy | Contact us
Site map | About Us | Employment
© Copyright 2014 Stewart-MacDonald
Your shopping is secure with VeriSign! Trusted Commerce