Stewart-MacDonaldEverything for building and repairing stringed instruments!
Your order cart Your order | Account | Saved list
Sign in
Email
800-848-2273, 9AM-6PM EST, M-F
Home Free catalog Quick order International Customer service

Home : Free Information : Finishing : Finishes, solvents : ColorTone Waterbase Sanding Sealer Instructions

ColorTone Waterbase Sanding Sealer Instructions

Directions for use



Email a friend

i-5573 Updated 12/13









 Processing...







ColorTone Waterbase Guitar Lacquers have been formulated to give a clear, hard, easy to apply and easy to repair alternative to current solvent finishes. The ColorTone waterbase product line includes stains, pigments, grain filler, sanding sealer, clear gloss topcoat and retarder. These materials can be used together exclusively, or used under and on top of many other products, such as shellac or lacquer.

Waterbase Sanding Sealer is a clear, hard, shrink-resistant polyester / urethane lacquer sealer. Successive sealer coats will bond best when applied within 48 hours of each other. When this time is exceeded, sanding with 320-grit paper is required to roughen the surface for adhesion of additional coats.

Preparation
Mix well. Stir gently, do not shake. Allow air bubbles to settle before straining and pouring into spray equipment.

ColorTone waterbase products require a clean, dust-free, wax-free surface for optimum performance. New wood should be sanded to 220-grit, vacuumed and blown dust free. If the surface has been contaminated with oils or waxes, wipe down with an equal mix of denatured alcohol and water. If the surface has been modified, clean and test waterbase products compatibility before proceeding.

Application
Waterbase finish doesn't look wet and glossy as you're spraying, unlike nitrocellulose. Be careful not to lay it on too thick, looking for that glossy wetness. Good lighting is very important. Spray light coats, carefully overlap your spray pattern by 1/3-1/2 for coverage with uniform thickness.

Optimum spraying condition is 70°F, and 45-60% relative humidity. Dry, oil and dirt-free air with proper ventilation is a must.
• For gravity feed spray gun, 40-60 psi with a tip size of 1.3mm is recommended.
• For siphon feed spray gun, tip size of 1.8mm is recommended.

Waterbase Retarder or water can be added to reduce viscosity. When hot/dry conditions cause the finish to dry too fast, thin with 5%-15% Waterbase Retarder.

Clean up
Clean spray equipment with warm, clean water immediately after each use. Do not leave lacquer in the spray gun for more than a few hours at a time. Remove dried finish with very hot water and alkaline cleaner, such as an all-purpose cleaner, degreaser or stripper). Store unused lacquer in a sealed container.

Keep out of the reach of children.

Keep from freezing.

EMERGENCY FIRST-AID PROCEDURES
INGESTION Do not induce vomiting. Administer large amounts of milk and seek medical attention.

EYES Flush with fresh water for 15 minutes. Seek medical attention.

SKIN Promptly wash with soap and water, and rinse thoroughly.

INHALATION Remove exposed person to well ventilated area. Seek medical attention if symptoms persist. USE IN WELL VENTILATED AREA. AVOID INHALING SPRAY.

COMPOSITION INGREDIENTS:
Compound Name CAS#
Acrylic Polymer Proprietary
Dipropylene Glycol Monomethyl Ether 34590-94-8
Water 7732-18-5
VOC Content: 32 Grams Per Liter








ColorTone Waterbase Sanding Sealer
ColorTone Waterbase Sanding Sealer


Toll-free order line:   800-848-2273   9am-6pm Eastern Time, M-F



Your order | Your account | Trade Secrets E-mail Newsletter
Home | Free catalog | Catalog Quick Order | International | Customer service
Our guarantee | Shipping | Security & Privacy | Contact us
Site map | About Us | Employment
© Copyright 2014 Stewart-MacDonald
Your shopping is secure with VeriSign! Trusted Commerce