Close

Ball Bearing Router Bits

4.5
  • 87 Reviews
  • Write a review
Ball Bearing Router Bits Router bit, 3/8" dia.

Router bit, 3/8" dia.

Item # 0583
Due 1-3 days
Notify Me

$26.95

+
Ball Bearing Router Bits Router bit,1/2" dia.

Router bit,1/2" dia.

Item # 0693
In stock, ready to ship!

$30.04

+
Ball Bearing Router Bits Extra bearing for 3/8" bit

Extra bearing for 3/8" bit

Item # 1288
In stock, ready to ship!

$5.90

+
Ball Bearing Router Bits Extra bearing 1/2" bit

Extra bearing 1/2" bit

Item # 1289
In stock, ready to ship!

$5.60

+
Ball Bearing Router Bits, Set of 2

Set of 2

Item # 0565
Due 1+ month
Notify Me

List Price $56.99
Your Price $52.43

+
 
Total:
Qty:
Scroll to Top

Ball Bearing Router Bits

About This Item

Special bits for templates! Extra-long carbide-tipped router bits produce clean, precise body cavities when used with our templates.

The ball-bearing guide matches the cutting diameter, and the long shank allows multiple-pass routing for deep cavities.

The 1/2" diameter bit is recommended for most of your routing chores, and comes with 1 bearing. Use the 3/8" cutter only for routing corners that need the tighter radius, it comes with 2 bearings.

Sold individually or SAVE when you buy the set of both router bits.

Shank diameter: 1/4" (6.35mm)
Cutting height: 1/2" (12.7mm)

A heat-resistant sleeve (not shown) holds the bearing in position. We recommend stacking an extra bearing on the shank for deep cavities, and use the 3/8" bit only for routing corners.

Tip: We recommend that you change the position of stacked bearings on the router bit's shank every time your re-chuck in the bit into your router. This will greatly extend the life of the bearings and reduces the risk of a bearing "blow-out."


Trade Secrets!

Trade Secrets!

How (and why) to use templates to rout control cavities

If you sometimes think of making a custom electric guitar, Erick Coleman has tips to make one part of the process a lot easier. Here's how to rout the neck pocket and control cavities so they look as good as a factory build.

Instructions

Product Instructions

Using Ball-bearing Cutter Bits for Guitar Routing

Instructions for using Ball-bearing Cutter Bits for guitar routing.

Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
4.5
  • 4.34 average rating from 87 reviews
Sort by
5.0

Just what the doctor ordered.

By
(Customer's Reviews)


I purchased both the half inch and 3/8 inch bits. They cut very clean. I would order an extra set of bearings. I found that two bearing stacked and the plastic sleeve was just the right combination I needed.

5.0

Ball Bearing Router bits

By
(Customer's Reviews)


Great stuff

5.0

Whammy walls and bits with balls!

By
(Customer's Reviews)


For a one time use, this bit worked great! Some have suggested to use 3/8 bit only on walls and 1/2 bit for the middle mass. This makes sense if your cutting two or three a week but for one I say it's all you need. The money I didn't spend on the 1/2" bit I used for spare 3/8" bearings for template depth and in case of a blow out.

Showing 3 of 87 Read more reviews >>


StewMac PDF Catalog, page 38 See Ball Bearing Router Bits
on page 38 of our StewMac Catalog PDF

12MB File

View with Adobe Acrobat Reader 4.0 or higher.
Download Adobe Acrobat free from Adobe.