Close

Golden Age Pre-wired Harness for Gibson® Les Paul®

4.5
  • 12 Reviews
  • Write a review

With standard-shaft CTS pots

Item # 1933
In stock, ready to ship!

$86.99

+

With long-shaft CTS pots

Item # 1934
In stock, ready to ship!

$98.99

+
 
Total:
Qty:
Scroll to Top

Golden Age Pre-wired Harness for Gibson® Les Paul®

About This Item

Assembled and soldered in the USA using top components, including Switchcraft switches and CTS pots for the best sound. Ready to drop into your guitar!

    Worth every penny!
  • Premium hand-wired for drop-in retrofit
  • Upgrade your old wiring
  • Save work and save time on new builds

Soldered in our Athens, Ohio shop
We professionally hand-soldered these harnesses using the best brand-name components for long life and great sound: CTS pots, Orange Drop® caps, Switchcraft™ toggle switch and output jack and cloth push-back wire.

Tested and 100% Guaranteed
Each Golden Age harness comes to you mounted on a reusable plywood template, which is a tool in itself: save it for future wiring jobs. The template holds the components correctly so the finished harness fits neatly into the guitar's wiring cavity.

Some simple soldering is needed to connect the switch and jack after you've threaded the wires through the guitar channels. Pickup lead wires will also need to be soldered to the harness.

Got questions? Call or email us. A friendly gearhead will be happy to help!

Switchcraft Toggle Switch Specs
Body cavity depth 1-1/2" (38.10mm)
Mounting hole diameter 1/2" (12.70mm)
Thread height 7/32" (5.56mm)

CTS Control Pot Specs
Resistance 500K-ohm
Shaft diameter 0.235" (5.95mm)
split shaft, fine knurling
Thread 3/8" x 32
Threaded portion 3/8" (9.52mm)
Threaded portion, long shaft 3/4" (19.05mm)
Required mounting hole diameter    3/8" (9.52mm)

Orange Drop Capacitor Specs
Value .022uF Code 223K

Switchcraft Output Jack Specs
Accepts standard 1/4" plugs Mono
Mounting hole diameter 3/8" (9.52mm)
Thread 3/8 x 32
Threaded portion height 1/4" (6.35mm)


Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
4.5
  • 4.67 average rating from 12 reviews
Sort by
5.0

Les Paul Pre-wired harness

By

Verified Buyer


My LP came with a circuit board with the pots soldered on. Not shielded. This harness is easy to install with minimal soldering. Not hard to do. I replaced pickups at same time with Parsons Street overwounds. MUCH better sound!

5.0

Epiphone les paul

By

Verified Buyer


Good solder connections. Only thing is, if you buy this for an epiphone, you will need a short shaft switch. All I did was unsolder the switch and put in a short shaft.

5.0

prewired gibson system

By

Verified Buyer


works great stopped allthe shorting when i moved guitar would recommend it to everybody

5.0

Les Paul pre-wired setup

By

Verified Buyer


The quality of the CTS pots and soldering was top notch. All I had to do was solder the ground from the guitar & the pickup leads and I was done. Job was done in less than an hour. Easy-Peasy!

5.0

Awesome

By

Verified Buyer


Super easy installation! Major time saver!

5.0

Pre-wired harness

By

Verified Buyer


Worked perfectly

4.0

Great Except

By

Verified Buyer


Snaked this right into my guitar without any problem. Fairly quick and easy. It would have been better if the ground wires were insulated though. I ran into some problems with grounds touching other components where it shouldn't and shorting. Just be careful routing your ground wires and tuck them away neatly or tape them up. Overall top notch as always.

4.0

5 stars for product, 1 taken off for Epiphone fit

By

Verified Buyer


These electronics are top notch and the soldering instructions are easy to follow BUT if you are upgrading/repairing a circa 2011 Epiphone Les Paul please note that the holes for the switch and pots will have to be drilled out to a slightly larger size than stock. I have a background in woodworking but for the novice this could be daunting.

4.0

Almost

By

Verified Buyer


Put this in my 2003 Epiphone . Night and day it does sound like new guitar . One problem I had was the switchcraft switch was to tall I needed a short switch for my 2003 Epi Les Paul standard . I am not sure if newer ones are the same , check the height if you are going to put this in an Epiphone guitar.

4.0

nice idea

By

Verified Buyer


if you have minimal soldering skills just buy all the parts and solder them together yourself. it is a cute packaging idea.

Showing 10 of 12 Read more reviews >>


StewMac PDF Catalog, page 56 See Golden Age Pre-wired Harness for Gibson® Les Paul®
on page 56 of our StewMac Digital Catalog



  • Les Paul® is a registered trademark of Gibson Guitar Corporation.