Conductive Shielding Paint

  • 55 Reviews
  • Write a review

Reduces hum, noise and radio interference.
The fastest and easiest way to shield pickup and control cavities. Perfect for tight spots.

Read more
Conductive Shielding Paint 1/2 pint (236.6ml)

1/2 pint (236.6ml)

Item # 0029
In stock, ready to ship!


Conductive Shielding Paint 1 pint (473.2ml)

1 pint (473.2ml)

Item # 0027
In stock, ready to ship!


Total: $0.00
Quantity: 20


Reduces hum, noise and radio interference.
The fastest and easiest way to shield pickup and control cavities. Perfect for tight spots.

When connected to electrical ground, the shielded surfaces help reduce noise, hum and radio interference. It cleans up with water while still wet, and dries overnight.

Brush on two or more coats of this waterbase dark gray conductive paint for best results (let dry between coats). Conductive shielding paint is supplied in a 1/2-pint can, sufficient for shielding several electric guitars, and in a money-saving 1-pint can. We recommend our conductive tape for best results when shielding smooth plastic pickguards.

California Residents: Click here for Proposition 65 information.

Product Instructions

Conductive Shielding Paint Instructions

Directions for using conductive shielding paint.

Ratings & Reviews

Conductive Shielding Paint

  • Based on 55 Reviews
Displaying 5 of 6 1 2 3 4 5 6
Write a review

Easy shield

By TomL from Sydney,Australia
(Customer's Reviews) Friday, July 01, 2011

I have made a copper foil shielded area in a Strat cavity and it was hard work.This paint is so easy to use.Slop on 3-4 coats and the job is done. I have a cheap Strat that sounded great but the hum was annoying loud. I painted under the pickup and control cavities and now the hum is so soft it is barely noticeable. Highly recommended for all guitars.

It's as simple as pie

By GuitarzanMoore from Columbiana, Ohio
(Customer's Reviews) Monday, June 27, 2011

Listen this shielding paint works perfect and fantastic. I have basically quit using copper foil except for tab over grounding to pickguard shield. Put a strip of copper foil and paint it over in the rout cavity and put it over a pickguard screw hole to bind the shields together. Also forget the day of drying, can anybody say hair dryer? Works fast and coats are on in minutes instead of hours. Duh try heating your work up and then painting that works too!

Bye Bye hiss and noise....

By Sid Slack from Tacoma, WA
(Customer's Reviews) Monday, June 20, 2011

Works Great to shield out all those pestie Radio waves. i use it in the pickup cavity and in the electronic cavity and it cuts the noise down to 99%

shielding paint

By santos from calif
(Customer's Reviews) Thursday, April 14, 2011

i love this stuff eazy to use in pick ups cavity,s and everywhere the tape wont if you want a quiet guitar with zero hum you need this and the copper tape i have 30 guitars all with both of these

The Best Shielding Option

By Brooks Holland from San Fransisco, CA
(Customer's Reviews) Sunday, April 03, 2011

If you have any routing work inside the control cavity this is a great solution. It's much easier than lining an area with copper foil. This is essential for any electronics installation inside a guitar in-which you need to re-shield an area..

A bit messy!

By Jocko from Scotland
(Customer's Reviews) Monday, March 28, 2011

Works well but is a bit messy to apply. Three coats (third over screw connection) made for good electrical connection. Cleans up with water when wet but don't get it on untreated wood or you will have a bit of sanding to do. Accurately mask all bits you DON'T want painted.

The Paint Beats Copper

By JeffD from Seattle,WA USA
(Customer's Reviews) Tuesday, March 22, 2011

Using this shielding paint makes an easy job of shielding your guitar. Only drawback is you need at least 3 coats and must allow a day between each to dry.

Allows accurate work

By Riccardo from Italy
(Customer's Reviews) Friday, March 18, 2011

Excellent product, practical, effective ...

A must

By Michael Grannis from Phoenix, Az
(Customer's Reviews) Thursday, February 17, 2011

I used this in both the electronics and pickup cavities and it works great. It will go in every instrument i have. Thank you stewmac

Very useful and convenient

By Jade Guitars from Herndon, VA
(Customer's Reviews) Monday, February 07, 2011

A superb, cost-effective and easy to use shielding product. We use this on all of our Drew & Sebastian custom guitars and basses. Highly recommended for the luthier and amateur alike, won't peel off like shielding tape.

Displaying 5 of 6
1 2 3 4 5 6

Shown on page 50 of our latest catalog.