Close

Conductive Shielding Paint

5.0
  • 75 Reviews
  • Write a review
Buy more, save more!
Conductive Shielding Paint 1/2 pint (236.6ml)

1/2 pint (236.6ml)

Item # 0029
In stock, ready to ship!

$32.82

+
Conductive Shielding Paint 1 pint (473.2ml)

1 pint (473.2ml)

Item # 0027
In stock, ready to ship!

$60.56

3 or more $53.35
+
 
Total:
Qty:
Scroll to Top

Conductive Shielding Paint

About This Item

Reduces hum, noise and radio interference.
The fastest and easiest way to shield pickup and control cavities. Perfect for tight spots.

When connected to electrical ground, the shielded surfaces help reduce noise, hum and radio interference. It cleans up with water while still wet, and dries overnight.

Brush on two or more coats of this waterbase dark gray conductive paint for best results (let dry between coats). Conductive shielding paint is supplied in a 1/2-pint can, sufficient for shielding several electric guitars, and in a money-saving 1-pint can. We recommend our conductive tape for best results when shielding smooth plastic pickguards.

California Residents: Click here for Proposition 65 information.

Instructions

Product Instructions

Conductive Shielding Paint Instructions

Directions for using conductive shielding paint.

Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
5.0
  • 4.80 average rating from 75 reviews
Sort by
Displaying 2 of 8
1 2 3 4 5 6 7 8
2.0

An option

By

Verified Buyer


I use it regularly with different results, some good, some not. Also Stewmac, quit buying the cheap cans from China as they rust out on the bottom from the inside. I lost half a can before I noticed.

Response from StewMac

Quality and 100% Total Satisfaction is our goal every day. If a product fails to work as intended in your shop, we'll take back the product and replace or refund. Call us 1-800-848-2273 so we can make it right.

In the meantime, I've placed your suggestion with our product development team -- customer comments like yours have been the catalyst to many changes to our products.

1.0

Conductive Paint not as good as copper tape

By

Verified Buyer


Put 5 coats on my pickup and electronic cavities and the best I could do was 27 ohms....I the bought some copper tape and achieved .2 - .3 ohms....with target being under 1....so I am never going to use the paint again ...the numbers don't lie...it's over priced and marginal at best!

Response from StewMac

Thank you for sharing your honest feedback with us. We're very sorry our Conductive Shielding Paint didn't work for you as expected. To get good results, it's very important to wait a full 24 hours between each coat. We stand behind our return policy -- if you are not satisfied you may return it for a refund or exchange. Please call us at 1-800-848-2273. We look forward to helping you with this.

5.0

It works

By

Verified Buyer


It's not copper but as long as you are not creating ground loops with your wiring or carrying any current at all in the shield it works, and it's very quick and easy to apply - although the recommended three coats will take three days.

5.0

Works great.  Follow the instructions.

By

Verified Buyer


I used this in the body cavity of a 1989 Fender Tele, which was completely unshielded. Worked great! Make sure you use at least three coats, and give each coat a full 24 hours to cure. Be careful also about tight cavities where a hot wire might brush against the paint -- if necessary, bend a connection away from the cavity wall and/or use some electrical tape to maintain good separation.

5.0

Great Product

By

Verified Buyer


Easy to use, easy clean up. Performs as expected. Would buy again.

5.0

Worked good for me

By

Verified Buyer


I used this on a customer build. Went on easy did a couple coats just to be sure, she loved it, don't get much better

5.0

Read the directions.

By

Verified Buyer


This product works very well. You will need clear access to all cavities and wire routes. I used shielded cables when I could not get the product into wire channels and then grounded the shields to the cavity areas. This product and foil shielding on the underside of the pick guard made a badly humming bass 99% silent. Ventilation and a fan for fumes are required.

5.0

I love it!

By

Verified Buyer


I'm totally shielding all of the cavities in my custom build Strat. This is so easy to use. Just make sure you mask the area around your work thoroughly and keep a small bowl of water and dish soap close at hand. The paint tends to flick off the brush easily as you paint the sides of the cavities. I'm so glad I bought this. It beats the heck out of trying to even out shielding foil.

5.0

great product

By

Verified Buyer


Used this for the cavity in conjunction with the self adhesive shielding kit for the pickguard of my PRS DC3 which was making a racket! worked great. it is messy and tends to get on things so be prepared with rags to wipe up any mistakes.

5.0

I'LL NEVER GO BACK TO SHIELDING TAPE!!!

By

Verified Buyer


I used this on an ash Tele body for a project I was building. I had used copper shielding tape on past projects and let me say, this just blows that tape away. I followed the instructions to the letter and this is absolutely the quietest guitar I've ever made. This stuff really does the trick. Now I'm thinking about going back and using it on some of my past projects. Great stuff! Buy it! You won't be disappointed!

Displaying 2 of 8
1 2 3 4 5 6 7 8


StewMac PDF Catalog, page 52 See Conductive Shielding Paint
on page 52 of our StewMac Catalog PDF

11.5MB File

View with Adobe Acrobat Reader 4.0 or higher.
Download Adobe Acrobat free from Adobe.