Replacement Neck for Strat Guitar

4.5
  • 45 Reviews
  • Write a review

Shaped, inlaid, fretted and finished—feels and plays great! Hard rock maple finished in clear satin polyurethane, with a walnut "skunk stripe" down the back.

Read more
Replacement Neck for Strat Guitar Rosewood fingerboard

Rosewood fingerboard

Item # 5715
In stock, ready to ship!

$100.00

+
Replacement Neck for Strat Guitar Maple fingerboard

Maple fingerboard

Item # 5716
In stock, ready to ship!

$118.75

+
Replacement Neck for Strat Guitar Compound radius, rosewood fingerboard

Compound radius, rosewood fingerboard

Item # 5713
In stock, ready to ship!

$110.00

+
Replacement Neck for Strat Guitar Compound radius, maple fingerboard

Compound radius, maple fingerboard

Item # 5714
In stock, ready to ship!

$135.00

+
Currency:
Total: $0.00
Quantity: 20

Details

Shaped, inlaid, fretted and finished—feels and plays great! Hard rock maple finished in clear satin polyurethane, with a walnut "skunk stripe" down the back.

The 22 frets are nicely finished, and the nut is shaped and slotted. Maple or rosewood fretboard with dot inlays and side markers.

Screwholes for attaching to the body are not drilled. Each neck has a truss rod with a 4mm adjusting nut at the peghead. We recommend Allen Truss Rod Wrench for adjusting neck relief.

Peghead is drilled for 6-in-line tuning machines. 11mm-diameter holes fit sealed gear tuners with threaded peghead bushing. See all tuners.

Specifications
Scale length 25-1/2" (647.70mm)
Width at nut 1-11/16" (42.86mm)
Width at 22nd fret 2-3/16" (55.56mm)
Fretwire .045" high x .095" wide (1.14mm x 2.41mm)
Approximate heel length 3-5/8" (92.07mm)
Fretboard radius 9-1/2" (241.30mm)

Compound radius necks
The fingerboard surface radius gradually changes from 9.5" at the nut, to 12" at the 22nd fret (241mm to 305mm), for lower action and cleaner string bending. 14.75" (375mm) bridge saddle radius is recommended.

Neck thickness (approximate; not including fret)


Ideally, the neck should just drop into the neck-pocket, or be a little snug. Don't force the neck into the pocket. If the body is unfinished, remember that the finish will make the neck pocket smaller with lacquer build up on the edge of the rout. Be sure to compensate for the finish buildup or the neck will be too tight after finishing.


Trade Secrets! Newsletter

Fine tuning a bolt-on replacement neck

Erick Coleman pulls his old Strat out of mothballs and gives it a new neck. He shows what's needed to get a replacement neck ready to play.

Ratings & Reviews

Replacement Neck for Strat Guitar

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
4.5
  • Based on 45 Reviews
Displaying 5 of 5 1 2 3 4 5
Write a review
5.0

Great quality necks!

By
(Customer's Reviews)


Hey guys, I've used your stat necks and uncut headstock necks on a variety of customer guitars and have always had great results. Strong and straight and perfectly fretted. In response to the review by Wilbury out of Russia, frets "sticking out" is common with all guitars, not a flaw. The weather in your part of Russia is probably less humid than where these were made. Things like electric heat sources will also help to dry out the wood in the neck, shrinking it slightly, and making the frets stick out so to speak. It's a common occurrence and a common repair for any workshop. I don't even think about it anymore, when a guitar comes in for a setup during the winter especially, I take a few minutes to do the fret ends.. (Using my trusty Stew-mac files) Again, great products guys!

1.0

Maple Strat Replacement Neck

By
(Customer's Reviews)


I was first very satisfied with this neck as it arrived. It looked and felt quite good, especially taking into account the price. But, unfortunately, after six months I noticed that all the frets began to stick out along the edges of the fretboard (quite painfully scratching fingers). I have to say that the neck was not exposed to any extreme conditions such as temperature changes or low humidity. The reason, I guess, might be that the neck and the frets 'set in' this way. Also I surmise that the frets might have been installed without glue. Alas, in my particular case Mighty Mite is really poor quality. I wish I'd paid more but had a better quality product.

5.0

Love the feel

By
(Customer's Reviews)


After cleaning up some sharp fret edges, and a slight head modification, this neck is perfect. I got the maple compound. Make shure you get the right bridge radius. I love it.

5.0

made for each other

By
(Customer's Reviews)


Over the years I've have built customers guitars, sometimes using using Stew-Mac necks and bodies built years apart .Yet they still fit like a glove , it's only fair to share glory with you guys as you did all the hard work

4.0

Pretty good for the price

By
(Customer's Reviews)


I was looking at buying used MIM Fender necks online but decided to buy one of these because they were a bit cheaper. The rosewood fingerboard feels nice, the frets are level and there doesn't seem to be any more buzzing than usual. A good neck for the money.

Displaying 5 of 5
1 2 3 4 5


Shown on page 73 of our latest catalog.
  • These necks are made for us by Mighty Mite, and have peghead shapes licensed by Fender.
  • Stratocaster® and Strat® are registered trademarks of Fender Musical Instruments Corporation.