Replacement Neck for Strat Guitar

5.0
  • 47 Reviews
  • Write a review
Replacement Neck for Strat Guitar Rosewood fingerboard

Rosewood fingerboard

Item # 5715
In stock, ready to ship!

$100.00

+
Replacement Neck for Strat Guitar Maple fingerboard

Maple fingerboard

Item # 5716
In stock, ready to ship!

$118.75

+
Replacement Neck for Strat Guitar Compound radius, rosewood fingerboard

Compound radius, rosewood fingerboard

Item # 5713
In stock, ready to ship!

$110.00

+
Replacement Neck for Strat Guitar Compound radius, maple fingerboard

Compound radius, maple fingerboard

Item # 5714
In stock, ready to ship!

$135.00

+
 
Total:
Qty:
Scroll to Top

Replacement Neck for Strat Guitar

Shaped, inlaid, fretted and finished—feels and plays great! Hard rock maple finished in clear satin polyurethane, with a walnut "skunk stripe" down the back.

The 22 frets are nicely finished, and the nut is shaped and slotted. Maple or rosewood fretboard with dot inlays and side markers.

Screwholes for attaching to the body are not drilled. Each neck has a single-action truss rod with a 4mm adjusting nut at the peghead. We recommend Allen Truss Rod Wrench for adjusting neck relief.

Peghead is drilled for 6-in-line tuning machines. 10mm-diameter holes fit sealed gear tuners with threaded peghead bushing. See all tuners.

Specifications
Scale length 25-1/2" (647.70mm)
Width at nut 1-11/16" (42.86mm)
Width at 22nd fret 2-3/16" (55.56mm)
Fretwire .045" high x .095" wide (1.14mm x 2.41mm)
Approximate heel length 3-5/8" (92.07mm)
Fretboard radius 9-1/2" (241.30mm)

Compound radius necks
The fingerboard surface radius gradually changes from 9.5" at the nut, to 12" at the 22nd fret (241mm to 305mm), for lower action and cleaner string bending. 14.75" (375mm) bridge saddle radius is recommended.

Neck thickness (approximate; not including fret)


Ideally, the neck should just drop into the neck-pocket, or be a little snug. Don't force the neck into the pocket. If the body is unfinished, remember that the finish will make the neck pocket smaller with lacquer build up on the edge of the rout. Be sure to compensate for the finish buildup or the neck will be too tight after finishing.


Trade Secrets!

Fine tuning a bolt-on replacement neck

Erick Coleman pulls his old Strat out of mothballs and gives it a new neck. He shows what's needed to get a replacement neck ready to play.

Customer Reviews

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
Write a review
5.0
  • 4.70 average rating from 47 reviews
Sort by
Displaying 3 of 5 1 2 3 4 5
5.0

Replacement maple neck for strat.

By
(Customer's Reviews)


Great product and excellent service, very happy very fast delivery just over 1 week. Will be using Stewmac again when I am purchasing anything else.

5.0

Quality neck at a value price.

By
(Customer's Reviews)


Actually the first one I got was simple to put on and quite frankly I really liked it but, it was cut in on one side between the 5th and 7th fret, very small problem but, I called StuMac and they replaced it, no problems with another very nice neck. It just does not get any better than that. I will add this, both necks had wonderful rolled frets right out of the box.

5.0

Beautiful.

By
(Customer's Reviews)


Aside from cleaning some sharp edges from the frets, this compound radius neck is everything a Strat lover could want. I like the action super low, and this neck allows that.

5.0

Strat maple neck

By
(Customer's Reviews)


Replaced a MIA rosewood with the compound all maple. Mounted well, sanded the fret ends slightly and that guitar is making some great sounds. Might replace the nut--but I know this is the neck that will stay on this guitar for a real long time. Love it. Now some new necks for the Squier 51! Great customer service too. Thanks.

4.0

Maple neck

By
(Customer's Reviews)


I ordered the one piece maple neck and I must say I am impressed! The grain is beautiful and the frets are set superbly. The neck is made by mighty mite which is mentioned on the website in the fine print(many customers failed to see it) My only complaint is that the nut is poor quality and I will have to replace it with a bone or lsr roller nut at some point. Thank you Stew mac for your amazing service and quality.

4.0

Squier strat replacement

By
(Customer's Reviews)


Replaced a Squire Strat neck with this. Major improvement. Had already replaced the electronics, which made it sound great, now it plays great, too.

5.0

It made the guitar

By
(Customer's Reviews)


I changed the neck on my Line 6 JT-69 Variax to a 5714 Compound Radius Maple neck and it made all the difference in the world. It went from being difficult to play, mediocre guitar to an instrument I am happy to play out on gigs. I highly recommend this neck swap.

5.0

StewMac Strat replacement neck

By
(Customer's Reviews)


StewMac Strat replacement neck, rosewood, compound radius. Great choice. Awesome. I put some Shaller tuning keys on. Plays great. Intonation is perfect. I wouldn't change a single thing. 110% satisfied!

5.0

Good neck ever ! but too much pressed frets

By
(Customer's Reviews)


This neck is good. Response is good. But one or two frets was really crushed.It seems be too much pressed .I must level the frets .This is not a too much problem for low price and high quality.

5.0

je suis totalement (flabergaster)

By
(Customer's Reviews)


En effet, le manche est totalement parfait a lÆexception du bord des frets qui Tcorchent les doigts lTgFrement mais ce petit dTtaille est trFs facilement remTdiable. En fait il est tellement bien que jÆhTsite a installer le lock nut a propos si vous avez des suggestions jÆapprTcierais beaucoup vos commentaires. Merci! je suis totalement (flabergaster)!

Displaying 3 of 5
1 2 3 4 5


Shown on page 75 of our latest catalog.
  • These necks are made for us by Mighty Mite, and have peghead shapes licensed by Fender.
  • Stratocaster® and Strat® are registered trademarks of Fender Musical Instruments Corporation.