Slotted Fingerboard for Fender Guitar

4.5
  • 43 Reviews
  • Write a review

25.5" scale • 12" radius • 24 slots + nut slot
Each fingerboard is radiused and extended to include a 1/8" flat-bottomed nut slot, Fender style.

Read more
Slotted Fingerboard for Fender Guitar Ebony

Ebony

Item # 1062
In stock, ready to ship!

$47.62

+
Slotted Fingerboard for Fender Guitar Maple

Maple

Item # 1062-M
In stock, ready to ship!

$14.30

+
Slotted Fingerboard for Fender Guitar Rosewood

Rosewood

Item # 1062-R
In stock, ready to ship!

$21.65

+
Currency:
Total: $0.00
Quantity: 20

Details

25.5" scale • 12" radius • 24 slots + nut slot
Each fingerboard is radiused and extended to include a 1/8" flat-bottomed nut slot, Fender style.

Tip: Saw the fingerboard shorter at the 2nd fret (at the nut end) to install it on a Gibson 22-3/4" short scale guitar.

Our kiln-dried fingerboards have flat undersides, are unfretted (no inlays), and ready for trimming to fit a variety of neck widths.

Approximate dimensions: 2-3/8" x 20-3/8" x 15/64" (60.32mm x 517.53mm x 5.95mm)
Radius: 12" (304.80mm)
Fret slots: 24 slots, 0.023" wide (0.58mm). Ready to accept our fretwire.
Nut slot: 1/8" wide (3.18mm)

A note about ebony:
Ebony is usually not uniformly black. We offer Black Fingerboard Stain, as used by Gibson, Paul Reed Smith and other makers, for darkening the streaks on ebony fingerboards, bridges and peghead overlays when desired.


Ratings & Reviews

Slotted Fingerboard for Fender Guitar

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
4.5
  • Based on 43 Reviews
Displaying 2 of 5 1 2 3 4 5
Write a review
5.0

Maple fretboard slotted for Fender

By
(Customer's Reviews)


I use these for one off guitars. I've used a few to create a 24 inch scale putting a zero fret in the first fret slot and sawing off the remainder. These always seem to seat the fret very well and are very level. I've never had any buzz anywhere on the neck. I'll keep using them and would highly recommend them.

4.0

Very good.

By
(Customer's Reviews)


I ordered the Rosewood fingerboard for my first project. It is a beautiful piece of wood, and the slots are perfect. There is a bit of planer chip-out behind the second fret, and it may or may not sand out; if I were building a 2,000-3,000 dollar guitar, it would be an issue, but I'm not, and it won't affect the sound or playability so I don't mind. Not perfect, but probably an outlier

5.0

Slotted fingerboard

By
(Customer's Reviews)


Radius work required but very good quality fingerboard

5.0

Rosewood fingerboard

By
(Customer's Reviews)


I installed 2 fretboards so far, both were excellent quality, but I noticed that one chipped more when routing it. But I had a little worn router bit.

5.0

Excellent fretboard!

By
(Customer's Reviews)


I just finished a new build and for the first time used a pre-slotter, radiused fingerboard. I purchased the rosewood with a 12" radius. It was excellent quality wood and very attractive. There were no blimishes at all, front or back and having it slotted saved me a lot of time and for just over $20 it was more than worth it.

5.0

Ebony fretboard

By
(Customer's Reviews)


Good quality wood, perfect fret slots, work required on the radiused side.

4.0

i had some problems

By
(Customer's Reviews)


unfortunately the item had a cut near the 12th fret on the surface. this is not a thing that could make it a bad quality product, but this shouldn't happen

5.0

perfecto

By
(Customer's Reviews)


Always perfect and a joy to work with. One of the many excellent deal on Stewmac!

5.0

Radius!

By
(Customer's Reviews)


I did not notice that the description of the item states that this is pre radiused. You should make stand out a little bit more.

Besides for that - the measurements are accurate and the wood is of high quality.

4.0

Good stuff!

By
(Customer's Reviews)


I like this maple fingerboard, beautiful and flawless.

Displaying 2 of 5
1 2 3 4 5


Shown on page 77 of our latest catalog.