Plastic Side Dot Material

  • 42 Reviews
  • Write a review

6" plastic rods for making position dot markers on the edge of a fingerboard. Cut and scrape the material flush after insertion.

Read more
Plastic Side Dot Material White, 1/16" diameter

White, 1/16" diameter

Item # 0483
In stock, ready to ship!

$1.15

24 or more $0.76
+
Plastic Side Dot Material Black, 1/16" diameter

Black, 1/16" diameter

Item # 0484
In stock, ready to ship!

$1.15

24 or more $0.76
+
Plastic Side Dot Material White, 3/32" diameter

White, 3/32" diameter

Item # 1358
In stock, ready to ship!

$1.15

24 or more $0.76
+
Plastic Side Dot Material Black, 3/32" diameter

Black, 3/32" diameter

Item # 1359
In stock, ready to ship!

$1.15

24 or more $0.76
+
Quantity Discount Prices apply when you buy multiples of the same item number.
Currency:
Total: $0.00
Quantity: 20

Product Details

6" plastic rods for making position dot markers on the edge of a fingerboard. Cut and scrape the material flush after insertion.


Ratings & Reviews

Plastic Side Dot Material

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
  • Based on 42 Reviews
Displaying 4 of 5 1 2 3 4 5
Write a review

Great Side Dot Material

By longtermsurvivor from Summerville, SC
(Customer's Reviews) Sunday, June 26, 2011


Stew-Mac side dot material is easy to work with and yields perfect results.

Clean little dots

By agnusguitars from champaign, il
(Customer's Reviews) Friday, June 17, 2011


I got the 1/16 black and it works just fine. I made an error and dipped the tips in my binding cement then placed in my pre-drilled holes. This turned out to be too much cement and sort of melted the thin rod and a few fret markers came out blurry even after scrapping. Next time I'll use a toothpick or just use super glue sparingly from a fine tip to fill the holes.

Side Dot Plastic

By Pick from New Zealand
(Customer's Reviews) Friday, June 03, 2011


Not much you can say about a thin rod of plastic! But it works just as it should.

Good Quality Item

By A. Lucas from Canada
(Customer's Reviews) Wednesday, May 25, 2011


It's a black plastic rod...not much to say really other than it goes in easily and it of nice quality.

Brainless

By Bookersdad from Randolph, Vermont
(Customer's Reviews) Saturday, May 14, 2011


This is a great product, effortless to install. One rod does many instruments.

Silly Easy!

By Whodatpat from College Park MD
(Customer's Reviews) Monday, April 11, 2011


This is the single easiest part of making a guitar and quickly rewarding too. these look great. One stick is enough for a few guitars. Both sizes look great so it is all your taste.

Easy as pie

By scottdes from michigan
(Customer's Reviews) Saturday, April 09, 2011


Great little item. Lasts forever, quality part.

work great!

By smashedguitars from San Antonio, TX
(Customer's Reviews) Thursday, March 24, 2011


Ive used these on many guitars over the years... mark a spot with a center punch, drill and super glue... all good!

side dot material is A#1

By Donnie Humphries-Lefthan Guitars from Cumberland, MD.
(Customer's Reviews) Wednesday, January 19, 2011


High everyone,Don the maddog luthier here to tell everyone about the side dot material available from Stewmac. Using an 1/8" drill bit,and some medium superglue is all it takes. The drill bit give a slight bit of wiggle room, which is great for the glue to get to all the surfaces,after drying I just come in with my flat surface nippers(fretting),cut, use a scraper for final surfacing. The material takes on finish very well,no complaints here. I can do 3-4 fingerboards per stick,and always try to keep some on hand.

Inexpensive, easy to install.

By Colt W. Knight from South Charleston, WV 25309
(Customer's Reviews) Friday, January 14, 2011


This work great. Inexpensive and easy to install. They will easily do several necks.

Displaying 4 of 5
1 2 3 4 5


Shown on page 32 of our latest catalog.