Plastic Side Dot Material

  • 42 Reviews
  • Write a review

6" plastic rods for making position dot markers on the edge of a fingerboard. Cut and scrape the material flush after insertion.

Read more
Plastic Side Dot Material White, 1/16" diameter

White, 1/16" diameter

Item # 0483
In stock, ready to ship!

$1.15

24 or more $0.76
+
Plastic Side Dot Material Black, 1/16" diameter

Black, 1/16" diameter

Item # 0484
In stock, ready to ship!

$1.15

24 or more $0.76
+
Plastic Side Dot Material White, 3/32" diameter

White, 3/32" diameter

Item # 1358
In stock, ready to ship!

$1.15

24 or more $0.76
+
Plastic Side Dot Material Black, 3/32" diameter

Black, 3/32" diameter

Item # 1359
In stock, ready to ship!

$1.15

24 or more $0.76
+
Quantity Discount Prices apply when you buy multiples of the same item number.
Currency:
Total: $0.00
Quantity: 20

Product Details

6" plastic rods for making position dot markers on the edge of a fingerboard. Cut and scrape the material flush after insertion.


Ratings & Reviews

Plastic Side Dot Material

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
  • Based on 42 Reviews
Displaying 3 of 5 1 2 3 4 5
Write a review

Plastic Side Dot Material

By Gusty from Ro
(Customer's Reviews) Friday, July 06, 2012


Excellent

plastic

By OTANIEL from CASCAVEL, PR, BRASIL
(Customer's Reviews) Tuesday, May 15, 2012


gostei...

Simple but right

By Danny Clayburn from Albuquerque, NM
(Customer's Reviews) Thursday, March 08, 2012


Almost felt silly about ordering a plastic rod, but it did the job perfectly. Just needed to add 3 dots to a tricone restoration, these are perfectly and consistently sized. Cut pretty easily with a razor, and also seemed to 'chip out' nicely when leveled, as opposed to distorting or bending.

Easy, effective

By Jeff Wolters from Exeter, NH
(Customer's Reviews) Thursday, March 01, 2012


Small extruded rods good for at least two necks. I am new to neck work and was impressed with how good this looked on first try with the StewMac maple binding. I used a zero-kerf hobby blade to cut, Super glue and no filler. Light sanding and done - easy!!

black dot for les paul

By DT from New-brunswick
(Customer's Reviews) Monday, February 13, 2012


needed to install side dot on my fingerboad. Stewmac had just hte perfect part to do the job

These little sticks go a long way!

By Rayzor from Lenawee county Michigan
(Customer's Reviews) Friday, November 18, 2011


A buck a strip and I get maybe 5 necks out of 1. But value is not really a value unless there is a certain level of quality that goes with it. I've used both sizes and colors, they all fit the stated hole size perfectly, no problem. Drill my holes first, put a drop of medium CA glue on a plastic lid and GO! dip the end a tad in the glue and it lubricates its way to the bottom of the hole. Trim long with a razor, cutters deform the material and then wont go into the next hole without dressing, then sand flat to the freboard. Easy-breezy.

Excellent

By p gaudreau from canada
(Customer's Reviews) Friday, November 18, 2011


Excellent

Inexpensive & works just as it should

By Nissan Hayun from Israel
(Customer's Reviews) Wednesday, September 28, 2011


You can easily mark 3-4 fingerbords with one rod

Super Easy

By TisDale Custom Guitars from Renton, WA, USA
(Customer's Reviews) Wednesday, September 07, 2011


Easy to work with, one piece can do 2-3 guitars depending on how long your insert is.

Works well, but the color is in a spectrum of it's own

By Jon Pruett from Washington, DC
(Customer's Reviews) Thursday, June 30, 2011


This stuff is very simple to install, but be aware the white is a very bright pure white and will look quite different from mother of pearl (or imitation) fret markers.

Displaying 3 of 5
1 2 3 4 5


Shown on page 32 of our latest catalog.