Piloted Router Bit for Binding

  • 16 Reviews
  • Write a review

Carbide-tipped to stay sharp longer! Special cutters for routing precise binding channels, with a pilot extension for uniform routing depth.

Read more

For 0.060" channel

Item # 4561
In stock, ready to ship!

$22.45

3 or more $19.98
+

For 0.090" channel

Item # 4562
In stock, ready to ship!

$22.45

3 or more $19.98
+
Quantity Discount Prices apply when you buy multiples of the same item number.
Currency:
Total: $0.00
Quantity: 20

Product Details

Carbide-tipped to stay sharp longer! Special cutters for routing precise binding channels, with a pilot extension for uniform routing depth.

Carbide tips stay sharp longer than steel bits. Small diameter makes them ideal for tight curves.

Binding router bits for Dremel & Foredom tools.
To use our 1/8"-shank bits in your laminate trimmer's 1/4" collet, use our Adapter Collet.

For channel width Shank diameter Cutting height
#4561 Pilot bit for .060" (1.52mm) channel 1/8" (3.18mm) 3/8" (9.52mm)
#4562 Pilot bit for .090" (2.29mm) channel 1/8" (3.18mm) 3/8" (9.52mm)


Ratings & Reviews

Piloted Router Bit for Binding

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
  • Based on 16 Reviews
Displaying 1 of 2 1 2
Write a review

Good option

By Dave (Union Guitars) from Australia
(Customer's Reviews) Friday, February 14, 2014


All binding channel cutting tools have their limitations and quirks. I have use a few - and when used carefully, and with a light hand, this simple bit has been one of the best. Gives a nice straight, uniform channel with very little set-up time required, and can get into tight spaces. Would be nice to have a few more sizes - how about 0.040" ?

Excellent alternative to a ball bearing bit

By Jon Anderson from Saint Paul, MN
(Customer's Reviews) Wednesday, September 18, 2013


If you only need a bit to cut for .060" or .090" these bits work very well. The pilot does not burn or burnish the workpiece if a light touch and constant motion of the tool are employed. Stays sharp as long as any other quality router bit.

pilot routing bit

By Wayne's Guitars from Amherst, NY
(Customer's Reviews) Wednesday, April 03, 2013


Great little bit. Yeah,it leaves a small burn mark, a little sanding takes it out. It's a bit pricey but for what it does, it's worth it. Thanks Stew-Mac, as always, great products!

Worked OK but needs bearing

By Ian Verner from Sydney, Australia
(Customer's Reviews) Sunday, August 19, 2012


Worked OK but the scar left by the spigot make clean up more difficult. need to have bearing option

Tips For Piloted Roter Bit Use

By Branzell Guitars from Spring Creek NV
(Customer's Reviews) Wednesday, January 18, 2012


For those who are struggling with a burned or marred line from the pilot try this. Route before you finish sand the thing! Glue the binding in, then sand the burn or line out. Climb cut with this bit to eliminate tearout. Make shallow climb cuts at first. I've been building for many years and there is a learning curve like no other in the luthier field. These bits are awesome I have been using them for years.

This is a terrible bit!

By HippieDave from Caspar, CA
(Customer's Reviews) Saturday, December 31, 2011


Do not think of using this. It needs a bearing, not just a shaft guide. Gouged the wood the first time I used it and then it got dull immediately anyway.

Excellent bit but take your time.

By Pete M. from San Antonio, TX
(Customer's Reviews) Thursday, September 15, 2011


This bit seemed expensive to me until I got it and used it. It cuts exceptionally well and you get what you pay for, right? Some people have complained about the pilot leaving a mark. I have found that if you let it cool off for a minute here and there you won't have that problem.

Good Clean up Tool

By Bill from Puyallup from Puyallup WA
(Customer's Reviews) Thursday, August 04, 2011


This was an excellent cleanup tool for those where the depth and height may be a bit off from using your binding bit/bearing purchased from Stewmac.com, especially around top back of a guitar where the neck and body meet.

The curve is steeper here, so instead of using a wedge while binding, just use this bit in your Dremel tool to tweak the channel a bit until the binding fits flush. It cuts a nice neat channel, although you do have get used to it as likes to wander a bit if you go too fast. If you go slow you will get a good looking clean channel every time

Worked Perfect

By JasonM from Slidell, La
(Customer's Reviews) Sunday, July 31, 2011


Used this to route the binding channel on the headstock of my acoustic guitar project. Yes, there is a small mark left behind on the wood from the guide, but that did come out quite easily when sanding the binding flush with the headstock.

Router Bit Works Fine

By The Lefty Luthier from Spring Branch, Texas
(Customer's Reviews) Saturday, July 09, 2011


This bit works as advertised providing extreme care is used on end grain. A spiral cutter would work much better.

Displaying 1 of 2
1 2


Shown on page 31 of our latest catalog.