Ball Bearing Router Bits - Set of 2

  • 84 Reviews
  • Write a review

Special bits for templates! Extra-long carbide-tipped router bits produce clean, precise body cavities when used with our templates.

Read more

Ball Bearing Router Bits - Set of 2

Item # 0565
In stock, ready to ship!

$56.70 $52.16

+
Currency:
Total: $0.00
Quantity: 20

Product Details

Special bits for templates! Extra-long carbide-tipped router bits produce clean, precise body cavities when used with our templates.

The ball-bearing guide matches the cutting diameter, and the long shank allows multiple-pass routing for deep cavities.

The 1/2" diameter bit is recommended for most of your routing chores, and comes with 1 bearing. Use the 3/8" cutter only for routing corners that need the tighter radius, it comes with 2 bearings.

Sold individually or SAVE when you buy the set of both router bits.

Shank diameter: 1/4" (6.35mm)
Cutting height: 1/2" (12.7mm)

A heat-resistant sleeve (not shown) holds the bearing in position. We recommend stacking an extra bearing on the shank for deep cavities, and use the 3/8" bit only for routing corners.

Tip: We recommend that you change the position of stacked bearings on the router bit's shank every time your re-chuck in the bit into your router. This will greatly extend the life of the bearings and reduces the risk of a bearing "blow-out."


Trade Secrets! Newsletter

How (and why) to use templates to rout control cavities

If you sometimes think of making a custom electric guitar, Erick Coleman has tips to make one part of the process a lot easier. Here's how to rout the neck pocket and control cavities so they look as good as a factory build.

Product Instructions

Using Ball-bearing Cutter Bits for Guitar Routing

Instructions for using Ball-bearing Cutter Bits for guitar routing.

Ratings & Reviews

Ball Bearing Router Bits - Set of 2

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
  • Based on 84 Reviews
Displaying 6 of 9 1 2 3 4 5 6 7 8 9
Write a review

sweet

By Joes Guitars from Todd Mission, TX
(Customer's Reviews) Monday, June 13, 2011


these bits are very clean cutting.

great value

By bob1319
(Customer's Reviews) Tuesday, May 31, 2011


for the builder who only need a few bits, these pattern bits work perfectly for control cavity routing, pickup cavities, everything. of course they can't route most neck pockets, as they are too small. For every other cavity, they are perfect.

Perfect and smooth cut

By Cristiano Bochese from Verona, Italy
(Customer's Reviews) Sunday, May 29, 2011


I had to order a 1/4" collar for my router (I had only 6 and 8 mm), but then I've been able to use them. I'm very happy 'cause they works very well (fast and smooth cut). Yeah!!!

Nice clean cuts.

By Jerhico Guitars from Altona, NY
(Customer's Reviews) Monday, May 09, 2011


As the title says. But like Mickey Springer from Hollywood,CA says, these do cut slightly bigger than the bearing. I just add a strip of tape to the template to fix it that problem. These are super sharp and leave clean edges and last a long time if you maintain them properly. That's right, you should clean the bits when they get too dirty. Keeps them sharper and cooler so they last longer.

Ball Bearing Router Bits

By DuctTapeNinja from Chicago
(Customer's Reviews) Monday, May 09, 2011


I've used both the 3/8" and the 1/2" bits, and they both cut larger than the bearing. This means that your bit will cut more of the project than you want, and depending on the depth of the route, it'll probably cut into the template you're using ruining it.



Then we have the poor bearing life. I only got the 1/2" bit last week, so its bearings haven't worn out yet. But the bearings for the 3/8" bit (I even used 2 as recommended to increase bearing life) wore out extremely fast.

precise

By fret from athens greece
(Customer's Reviews) Sunday, May 08, 2011


every time i say precise my mind goes to these router bits

doesn't work with stewmac templates

By Mickey Springer from Hollywood,CA
(Customer's Reviews) Wednesday, May 04, 2011


the blade cuts wider than the bearing.
there is a big gap between the bearing and the blade so unless you use a really thick template (the stewmac ones i got are not)the bearing is too high to make contact with the templates.

Beautiful

By Julyan Wallis, Guitar Doctor UK from Cornwall, UK
(Customer's Reviews) Wednesday, May 04, 2011


So reliable esp when used with the templates, the pro look is def achieved.
I find their shelf life very good indeed.

Great bits, easy to use

By Modern Saint from So Cal
(Customer's Reviews) Monday, May 02, 2011


For my first rout these were great. I didn't have any issues at all and would buy them again if I need too.

Bits good, bearings...not so much

By Robb from Ambridge, PA, USA
(Customer's Reviews) Saturday, April 23, 2011


The bits are fine quality, but the bearing leaves a bit to be desired, longevity-wise.

Displaying 6 of 9
1 2 3 4 5 6 7 8 9


Shown on page 36 of our latest catalog.