Ball Bearing Router Bits - Set of 2

  • 84 Reviews
  • Write a review

Special bits for templates! Extra-long carbide-tipped router bits produce clean, precise body cavities when used with our templates.

Read more

Ball Bearing Router Bits - Set of 2

Item # 0565
In stock, ready to ship!

$56.70 $52.16

+
Currency:
Total: $0.00
Quantity: 20

Details

Special bits for templates! Extra-long carbide-tipped router bits produce clean, precise body cavities when used with our templates.

The ball-bearing guide matches the cutting diameter, and the long shank allows multiple-pass routing for deep cavities.

The 1/2" diameter bit is recommended for most of your routing chores, and comes with 1 bearing. Use the 3/8" cutter only for routing corners that need the tighter radius, it comes with 2 bearings.

Sold individually or SAVE when you buy the set of both router bits.

Shank diameter: 1/4" (6.35mm)
Cutting height: 1/2" (12.7mm)

A heat-resistant sleeve (not shown) holds the bearing in position. We recommend stacking an extra bearing on the shank for deep cavities, and use the 3/8" bit only for routing corners.

Tip: We recommend that you change the position of stacked bearings on the router bit's shank every time your re-chuck in the bit into your router. This will greatly extend the life of the bearings and reduces the risk of a bearing "blow-out."


Trade Secrets! Newsletter

How (and why) to use templates to rout control cavities

If you sometimes think of making a custom electric guitar, Erick Coleman has tips to make one part of the process a lot easier. Here's how to rout the neck pocket and control cavities so they look as good as a factory build.

Product Instructions

Using Ball-bearing Cutter Bits for Guitar Routing

Instructions for using Ball-bearing Cutter Bits for guitar routing.

Ratings & Reviews

Ball Bearing Router Bits - Set of 2

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
  • Based on 84 Reviews
Displaying 4 of 9 1 2 3 4 5 6 7 8 9
Write a review

Worked like a charm!

By Kaarlo from Banff, AB. Canada
(Customer's Reviews) Monday, May 28, 2012


As always, shipped super fast! The bit along with the bridge template made this job a breeze (add a few extra bearings while your at it to your order as they come in handy as your rout deeper). Attached is the initial rout for the Tremolo Bridge from StewMac, which I will send a review on once job is complete! Thanks SM!

Nice bits

By RLowVaughn from Boise, Id.
(Customer's Reviews) Monday, April 02, 2012


The best bit I've found to make perfect pickup routs along with the StewMac templates.

excelente

By OTANIEL from CASCAVEL, PR, BRASIL
(Customer's Reviews) Wednesday, March 28, 2012


otima fresa para tupia... adorei,.

almost perfect

By Steeve Rock from L+¬vis, Qu+¬bec, Canada
(Customer's Reviews) Tuesday, March 06, 2012


they work great! but for some places I had to route, a 3/8" deep would've been better!

Router 3/8  bit with bearing

By Robert Houle from Montreal, Canada
(Customer's Reviews) Thursday, February 09, 2012


The story is that I add purchase a tTlTcaster Ash body and the neck pocket was to shallow by 1/16 to fit a standard neck. So I purchace the 3/8 bit to match the radius of the pocket corners. Did a test run on a scrap piece of wood, , then use a neck templare to do the routing,. This bit is of best quality and the finish was perfect, in fitted the neck in the pocket and all was level. Thanks to SM for there good tools and tips.

Ok but wear out quick

By DT from New-brunswick
(Customer's Reviews) Friday, February 03, 2012


this bit are ok for if you dont have alot of carving to do. They work great at first but become dull quickly. Especially in hardwood

VERY sharp

By Tiunov (22) from Moscow, Russia
(Customer's Reviews) Monday, January 23, 2012


Good bits and bearings, cut precisely and quickly.

Great bits

By Chris Bredenkamp from Durban, South Africa
(Customer's Reviews) Thursday, November 24, 2011


These are the best routing bits I have in my shop. They slice out pickup cavaties with maximum precision. I just wish the shanks were longer for cutting body shapes along a template.

Ball Bearing Router Bits

By Daniel G. Luthier from Canada, Q+¬bec
(Customer's Reviews) Tuesday, November 01, 2011


Ces la premiFre fois que je les utilisent et ta ses trFs bien passer, je n'ai pas ruiner mon gabarit et la coupe est trFs net et 1/2 pouce de long ces super car je ne suis pas obliger de mFtre un shime super Tpais ce que j'aurais TtT obliger de faire avec un couteau de 1 pouce d'une autre compagnie. Avec ces couteau je suis plus prFs de la surface a travailler a cause de ta logueur et avec trois bearings je suis svre d'avoir un bon contact avec mon gabarit. Super. Daniel G Luthier

Good bits

By Chester V from Pointe Claire,  Quebec, Canada
(Customer's Reviews) Wednesday, October 19, 2011


If you are using the Stew Mac templates
these are the only bits available that can be used. Off the shelf bits are too long and make too deep a cut. They are on the expensive side though.

Displaying 4 of 9
1 2 3 4 5 6 7 8 9


Shown on page 36 of our latest catalog.