Acoustic Bridge Locating Pins, Package of 6

  • 10 Reviews
  • Write a review

Temporary place holders to keep your pin bridge in place during gluing and setup. Non-stick. Reusable!

Read more

Acoustic Bridge Locating Pins, Package of 6

Item # 4602
In stock, ready to ship!

$4.98

3 or more $3.93
+
Quantity Discount Prices apply when you buy multiples of the same item number.
Currency:
Total: $0.00
Quantity: 20

Product Details

Temporary place holders to keep your pin bridge in place during gluing and setup. Non-stick. Reusable!

New smaller diameter works for new bridges as well as repairs, fitting both reamed, and unreamed pegholes.

One in each outer pin hole will do. They can be cut off above the bridge and below the bridge plate before clamping. Simply press them out after the glue dries.

Non-stick polyethylene pins are 1.6" long (40.72mm)
Each pin tapers from .265" to .116" (6.73mm to 2.95mm)


    • Item #
    • Weight
    • 4602
    • 0.017

Ratings & Reviews

Acoustic Bridge Locating Pins, Package of 6

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
  • Based on 10 Reviews
Write a review

another use

By tjt from maynard MA
(Customer's Reviews) Saturday, May 17, 2014


I use these locating pins to (re)open checks btwn bridge pin holes, simulating effect under string tension. Whack a few of these in the holes, apply #10 thin super glue, remove the non-stick locating pins, and voila! One more cool tool I didn't have to custom make. thanks guys!

Worked Very Well.

By Reds from Louisa, Virginia
(Customer's Reviews) Sunday, February 09, 2014


These were a great help when installing a new bridge. They were easily removed when the glue dried and the holes were clean.

Locating Pins - Good Idea

By SRW from Burleson, TX
(Customer's Reviews) Friday, November 08, 2013


For $5 I can't complain. These pins were too thick to use on my vintage Crown. Once they were firmly in place the bridge still had wiggle room. I'll shave a couple these to fit next the guitar.

Great value

By Little Crow from Atlanta, GA
(Customer's Reviews) Friday, June 01, 2012


For the cost of these, their usefulness is great. It made repairing a bridge much easier, allowing for quick alignment over the original holes and keeping the glue from flooding in to them.

simple, effective and a really good product

By Tom Sommerville from Singapore
(Customer's Reviews) Friday, February 17, 2012


This is such as simple item but it works really well and the glue does not adhere to them. Recent guitar in for a bridge reset but the peg holes were worn to the point where the pegs were loose in the holes. Normally I would use two of the pegs to align but in this case, that was not an option. Using the locating pegs completed the job beautifully. Oh! incidentally I did tell the customer he needed remedial action on his bridge which he declined.

Pretty good

By Dave Snider from Advance, North Carolina
(Customer's Reviews) Wednesday, September 28, 2011


I am on the same vein as a previous reviewer. These work very well-however they do require a little hand work to get the right diameter to fit into peg holes correctly. After that, they work great-just used them last week.

perfect

By JR Jenkins from Bakersfield, CA
(Customer's Reviews) Saturday, September 10, 2011


after checking and rechecking the measurements, turns out the bridge I had to reset was in the right place....tapped the two outer pins into the bridge, clamped, dried, perfect intonataion...great idea.

They Work

By Rob Leake from Brookfield ,IL
(Customer's Reviews) Friday, March 18, 2011


I buy several sets and custom cut them for each job. They keep the bridge plates in place when doing glue ups.

Made my job easy

By RDHMoore from Oakville, ON, Canada
(Customer's Reviews) Sunday, October 24, 2010


After the finishing was completed and I took off the tape from the face were the bridge had previously been bolted on I used these pins to locate the bridge in the the reamed holes for gluing the bridge on. Worked perfectly and no problem with them sticking in the bridge.

Bridge locating pins..

By Guitarman from WV
(Customer's Reviews) Wednesday, August 04, 2010


These pins do the job..they will hold your bridge right position.



Shown on page 23 of our latest catalog.