Close

Tuner Bushing Press

4.0
  • 19 Reviews
  • Write a review

Tuner Bushing Press

Item # 0460
In stock, ready to ship!

$58.01

+

Bushing Press Expansion Screw

Item # 0461
In stock, ready to ship!

$3.41

+
 
Total:
Qty:
Scroll to Top

Tuner Bushing Press

About This Item

Don't use a hammer!
Use this press for damage-free bushing installation and removal.

A fine instrument deserves care—our Tuner Bushing Press is the right tool for installing press-fit tuner bushings. Its steady controlled pressure helps protect the peghead finish, for a clean, professional looking job. It removes the bushings too, even stubborn bushings in counterbored pegholes.

    Improved!
  • See-through protective sleeve for bushing removal (no working blindly)
  • Clear protective peghead caul works with multiple bushing sizes

This convenient handheld tool was developed by Todd Sams here in our shop, and works with most major brands of guitar and mandolin tuning machines.

Best of all, it removes the bushings too!
Even stubborn bushings in counterbored pegholes can be removed easily and without damage, thanks to an adjustable expanding pin that grips the bushing from the inside.

Protects against serious peghead damage
As tight-fitting bushings come out of the peghead face, they often cause chips of dry wood and lacquer to pop up around the peghole. This is a well-known problem, and our Bushing Press protects against it in two ways:
1. Bushings are eased out gradually, without hammering.
2. We provide a clear protective caul that surrounds the bushing on the peghead face, holding the finish down as the bushing slides out.

    Included with the Tuner Bushing Press:
  • Brass pins for installing and removing bushings
  • Caul for protecting the peghead face
  • Allen wrench
  • Instructions


Instructions

Product Instructions

Tuner Bushing Press Instructions

An overview of how to install and remove tuner bushings with the Tuner Bushing Press.

Customer Reviews

  • Excellent
  • Good
  • Average
  • Fair
  • Poor
Write a review
4.0
  • 4.00 average rating from 19 reviews
Sort by
5.0

Great Little helper

By

Verified Buyer


I bought this thinking it may be a good addition to my guitar repairing tools.. I was right, it is such a handy gadjet for Stud removal without damaging the face of the Guitars Headstock when the Collars are removed..

I bought it for, and used it on, an old 1964 Australian made Maton guitar. I was so pleased I did as the Tuner ''Collars' were so thin at their sides, that I didnt want to risk using and old Nail punch to tap them out with, as some time ''Burring'' the end of the old tuner collars can Burr over rip out the Face plate wood on their way out... and thats a No No.
In the short time I have owned it, I have used it on 3 other older guitars with pushed in seated Collars with great ease, and with no ''mishaps'' from headstock veneer fractures.. its a very clean tool to use.. If you replace a reasonable amount of Machine Heads, take my advice, this is a very handy Tool to own.

5.0

Tuner Bushing Press 

By

Verified Buyer


This tool is fantastic. Just make sure you line up the top and bottom piece in a straight line. The bushings come out easy as 1-2-3. No more hammers to put in new bushings too. Great idea, great tool! Thanks guys!

5.0

Tuner bushing press

By

Verified Buyer


After reading the easy to follow instructions it was a breeze to install my new Waverly tuners and bushing. Thanks Stew Mac!

5.0

Bushing Press

By

Verified Buyer


This is a great tool ,It just makes things easy not really a demand tool but what can I say I am getting lazy as I age, Thanks guys for making it easy. Rick Gray

5.0

Makes the job so much easier

By

Verified Buyer


I was on the fence about getting this tool but now that I've used it, I don't know how I would have gotten the job done without it. The guitar I'm working is very old and non-standard to fitting the bushings by hand would likely not have worked. Great tool and worth the money for what it saves in aggravation.

1.0

very very very disappoint tool

By

Verified Buyer


too small, hard to handle, it can broke your finishing.....

i heat bushing and use some cut off acrilic clmap bushing. it fast and smooth than this tool.. REALLY DISAPPOINTMENT

1.0

Awkward tool...disappointed

By

Verified Buyer


Really difficult to handle and easier to mar the finish with this thing slipping than just driving them in with a hammer. Not bad for removing bushings, but too much money for not enough tool. I heat the bushings with a soldering iron and press them in with my closed drill press chuck. Works smooth every time.

4.0

Good product, works as advertised, but with a learning curve

By

Verified Buyer


I initially thought this product was a little gimmicky until I practiced with it for an afternoon on a beater neck. The instructions are pretty poorly written, so you have to read in between the lines. Beyond the instructions, I'd suggest making sure the neck is firmly held down via clamp/caul etc. in order to use this press/vise. You need both hands free to position the top and bottom attachments correctly, and if you are trying to simultaneously hold the headstock steady with half a free hand, I guarantee one of the swing attachments will fling loose at the worst possible moment and possibly scratch or dent your finish. You do have to kind of guide the top press each time you squeeze to keep it centered; otherwise it tends to push the bushing in a little off 90 deg unless you have it perfectly centered on the top and bottom of the hole - which may be possible with practice but very difficult for a beginner. Lastly I'd recommend taping or gluing some soft foam to the bottom anvil - it's hard plastic and it seems like it could scratch your finish pretty easily. So overall it's a little klugey, but with a little practice it works fine. There are plenty of other ways to press in bushings successfully (and much less expensive!), so I wouldn't say this is a "must have", but it works well for my needs.

3.0

It works, but...

By

Verified Buyer


Yes, it works and did the job, however, to use it was not as smooth as I expected from a quality StewMac tool.
Issues:
- The grip is very uncomfortable. I have small hands and with the jaws open for starting I almost couldn't have a firm grip on it because it was way to wide. With slightly curved grip maybe...?
- I used the stepped brass insert to remove the bushing and when it done the insert stuck in the hole and it took more time to set it free than to remove the bushing
- As others also said, the swiveling parts sometimes makes it awkward to use. The insert could shift very easily off from the proper direction pressing the bushing only on one side. Would be nice to have a screw to fix the position.
- The new bushing was black and the brass insert chipped the black finish at some points when I pressed them into the hole with it.
The basic concept is fine, but the production could be improved.

5.0

Great tool

By

Verified Buyer


Essential tool, excellentá

Showing 10 of 19 Read more reviews >>


StewMac PDF Catalog, page 21 See Tuner Bushing Press
on page 21 of our StewMac Digital Catalog