Fret Tang Nipper

4.5
  • 63 Reviews
  • Write a review

Undercuts fretwire, fast and easy.
Fret Tang Nipper speeds fret jobs on bound necks, and helps save the lacquer finish at the edges of unbound fretboards.

Read more
Fret Tang Nipper For Narrow Fretwire

For Narrow Fretwire

Item # 1604
In stock, ready to ship!

$60.93

+
Fret Tang Nipper For Medium Fretwire

For Medium Fretwire

Item # 1626
In stock, ready to ship!

$60.93

+
Fret Tang Nipper For Wide Fretwire

For Wide Fretwire

Item # 1649
In stock, ready to ship!

$60.93

+
Currency:
Total: $0.00
Quantity: 20

Details

Undercuts fretwire, fast and easy.
Fret Tang Nipper speeds fret jobs on bound necks, and helps save the lacquer finish at the edges of unbound fretboards.

Bill Collings (of Collings Guitars) inspired this clever tool for undercutting fretwire to fit over neck bindings. Insert the fretwire to the desired depth in the guide notch, squeeze the handle, and the wire is quickly and cleanly undercut—no bending or crimping.

For unbound fingerboards, too: try nipping the fret tang to length before installing the fret. Now you'll only need to cut and file the overhanging crown, and the fret will be less likely to twist and unseat.

A repair shop favorite!
  • Hardened-steel cuts clean and stays sharp
  • Rubber coated handles for a comfortable, non-slip grip
  • Tool is 5.5" long (140mm)

#1604 for narrow fretwire, 0.053" to 0.080" (1.35mm to 2.03mm) wide.
Narrow fretwire is typically used on banjos and mandolins.

#1626 for medium fretwire, 0.075" to 0.095" (1.90mm to 2.41mm) wide.
Medium is the most popular size of guitar fretwire.

#1649 for wide fretwire, 0.100" to 0.120" (2.54mm to 3.05mm) wide.
Wide is found on many modern electric guitars and basses.

Fret Tang Nipper is one of the few StewMac tools that is not recommended for stainless steel frets.


Ratings & Reviews

Fret Tang Nipper

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
4.5
  • Based on 63 Reviews
Displaying 5 of 7 1 2 3 4 5 6 7
Write a review
5.0

Almost perfect

By
(Customer's Reviews)


Ok Five stars because it saves so much time and effort and works pretty much flawlessly. StewMac by far has the best quality tools.

My only beef would be that some are rather pricey. But this is a device that does exactly what is says and does it very well.

5.0

So simple - So effective!

By
(Customer's Reviews)


Can't believe how much easier this little tool makes this job! Fast, accurate, easy. Not cheap, but worth the money.

5.0

Fret Tang Nipper

By
(Customer's Reviews)


This is a great little tool, reducing fretting time to about 20% of what it took filing each fret end before. It cuts accurately, and I can place and fit each fret in seconds.

4.0

Fret Tang Nipper

By
(Customer's Reviews)


Very nice piece of equipment; minor filing and you are ready to go....4 1/2 stars!

5.0

Fret tang nipper cuts the work down to size!

By
(Customer's Reviews)


This is a great tool. I used it to re-fret an unbound neck, and I was able to use this tool to cut the tangs and fit the frets so they did not extend past the fretboard. Also, using this tool made it easier to cut the individual frets from the fret wire. It's well worth the price!

4.0

Tang Nipper

By
(Customer's Reviews)


Works great, could be cheaper though in my opinion.

4.0

wonderful tool

By
(Customer's Reviews)


The reason I'm only giving this 4 stars is, that it's not absolutely foolproof. But with a bit of practice and care you can really cut off the tang nice and smooth with this. But it is easy to not hold the fret perfectly and then the cut will also not be perfect. But you'll figure that out in no time.

2.0

Blunt nipper

By
(Customer's Reviews)


I was dissappointed today when I went to do a re fret job on a bound fretboard (Can't be more than the 6th re fret that i've done with this tool)today and found my fret tang nipper had gone completely blunt. To the point where the cutting part has squashed down and bent into a curve. I tried to sharpen it but, after half a re fret job, i found that the same thing happened again. I think that this would be a better tool if the cutting part was made of stronger stuff. To be fair, the tool has already payed for itself but it would be so easy to make it better.

5.0

Great tool

By
(Customer's Reviews)


It does exactly what it says on the tin a great idea saves a lot of messing would recommend it.

5.0

Great tool!

By
(Customer's Reviews)


Works exactly like promised. All you have to do is check carefully where it cuts. A little filing is needed under the fret after the cutting but that's not a problem.

Displaying 5 of 7
1 2 3 4 5 6 7


Shown on page 13 of our latest catalog.