Adjustable Fret Slotting Saw, Saw only

  • 57 Reviews
  • Write a review

Our Fret Slotting Saw has a rigid brass spine, and a comfortable traditionally-turned hardwood handle with ferrule. It looks right at home on a luthier's workbench.

Read more
Adjustable Fret Slotting Saw, Saw only

Adjustable Fret Slotting Saw, Saw only

Item # 5744
In stock, ready to ship!

$29.21

+
Adjustable Fret Slotting Saw, Saw and depth stop

Adjustable Fret Slotting Saw, Saw and depth stop

Item # 5745
In stock, ready to ship!

$36.98

+
Currency:
Total: $0.00
Quantity: 20

Details

Our Fret Slotting Saw has a rigid brass spine, and a comfortable traditionally-turned hardwood handle with ferrule. It looks right at home on a luthier's workbench.

Sheffield steel blade.
Make no mistake: this is NOT a standard hardware megamart backsaw! We started with a blade of legendary corrosion-resistant Sheffield steel, and specified .023" width to match our fretwire. We insisted on precision pull-cut teeth, to greatly reduce blade flex and jamming in harder fingerboard woods. Lastly, we designed an easy to use, removable clear acrylic depth stop. It slides up or down, with thumbscrews to precisely set any fret slot depth.

And one more thing: this saw works seamlessly with our Fret Slotting Miter Box.

The acrylic depth guide can be adjusted to expose as much as 1/4" of the blade, and is removable for cutting off the ends of a blank fingerboard. It's also sold separately.

Overall length 15-1/4" (387.35mm)
Cutting length 10" (254mm)
Blade depth 1-3/4" (44.45mm)

Cut accurate 90-degree slots when you use the saw with our Fret Slotting Miter Box. Add a Fret Scale Template and you'll never miscalculate your fret positions.


Ratings & Reviews

Adjustable Fret Slotting Saw, Saw only

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
  • Based on 57 Reviews
Displaying 5 of 6 1 2 3 4 5 6
Write a review

Fret Saw and Slotting System

By Schwagdog from Pennsylvania
(Customer's Reviews) Wednesday, February 23, 2011


I found the Saw and mitre box system to be very strong and durable. I do however think the guide design could be a little better in that the set screws when tightened, push on the brass guides which then in turn move them out of flush or true. This can be remedied by using a metal spacer on the screw side (eliminating the movement when screwing in the set screws and protecting the housing from "set screw wear") . Overall a good system I would recommend if you do a lot of fret board work.

Fret Slot Saw

By Don Doerr from Lawton, MI
(Customer's Reviews) Thursday, February 17, 2011


The fret saw I purchased was an excellent purchase. The blade is of the proper thickness to prevent the blade from flexing and works well with the fret wire I purchased from Stewart-MacDonald. The all-wood handle is just the right size for a nice firm grip to prevent that untimely slip. Also, the ôspineö of the blade is rigged to keep the blade from bending and providing a large enough surface as stop for even a home made cutting jig.


I purchased the depth stop, which is made of clear plastic and an excellent investment. The set on the teeth is a bit much and makes it a little difficult to start the initial cut, but does a great job even with some of the hard woods I use. Overall I think itÆs a great tool and well made.

Fret Slotting Fixture

By Wayne Redditt from Wyebridge, Ontario Canada
(Customer's Reviews) Wednesday, January 26, 2011


The tool is decent quality and performs almost to expectations. Since there are no dimensional descriptions and the photos are not able to convey scale, a slight deficiency is not noted until you have the tool in your hands. The height of the guide blocks and guides will not allow a 1 inch thick neck blank (think Fender) under the guides and still function. This took a lot of time to fix. Perhaps a longer set of guides that extend higher, allowing the saw to clear a 1 inch neck blank should be made available as an option. For 1/4 thick fretboards the tool works exactly as advertised.

Timely delivery as usual. Thanks StewMac.

Fret saw

By lilbiker from tarpon springs, floriDUH
(Customer's Reviews) Wednesday, January 19, 2011


a good tool with hard ridge, made it easy to work with and was adaptable to other cuts too :)

Serra 

By Carlos Jos+¬ Machado Leal from Uberlandia  MG Brasil
(Customer's Reviews) Wednesday, January 12, 2011


Na minha opinipo foi a melhor ferramenta que foi projetada com regulagem de altura aplicada no trabalho da escala para facilitar o trabalho do luthier. No momento falta o Miter Box.



Carlos Leal - Uberlandia MG Brasil

Fretting Saw

By Mack Guitarworks from Hungary/Europe
(Customer's Reviews) Friday, January 07, 2011


Very good quality, cuts well in ebony too.

Fretting saw & miter box

By Robert Smith from Spring Grove, PA
(Customer's Reviews) Thursday, December 30, 2010


Miter Box is a must. Great. On my third saw, they dull easily, can sharpen only once. Next time will get the Jap saw.

Makes life a little easier. 

By RT Basses from Willow Street, PA
(Customer's Reviews) Wednesday, December 29, 2010


When used with the templates, it's very accurate. I was able to slot my first board in just a few minutes.

Fret saw and depth stop

By CarverDan from Ottawa Canada
(Customer's Reviews) Saturday, December 18, 2010


Being an avid woodworker/guitar maker/player, I have come up with some custom guitars for myself. Until recently, I just ordered the preslotted FB. Now,I decided to go into some custom ukele styles and because it is difficult to order FB with smaller scales. I decided to get the saw and depth stop and made my own miter box.


First use was for a Cigar Box guitar, using a S-M preslotted FB as a reference with a blank rosewood FB that I can get locally. Next I'm cutting fret slots for a 15 inch scale uke.

One flaw

By Lance from Ohio
(Customer's Reviews) Wednesday, December 15, 2010


In my opinion this is a great saw. It cuts fast and effortlessly. Only problem I have is the cut ends up being wider than the fret tangs. So if you buy this saw you will also need a fret fitter.(under pliers, nippers, etc.)

Displaying 5 of 6
1 2 3 4 5 6


Shown on page 15 of our latest catalog.