Bending Iron

  • 27 Reviews
  • Write a review

Variable temperature and versatile bending radii. Here's a well-made iron that's ideal for bending wet or steamed sidewood in the small shop.

Read more
Bending Iron Domestic, 120-volt

Domestic, 120-volt

Item # 0689
In stock, ready to ship!

$207.05

+
Bending Iron International, 220-volt

International, 220-volt

Item # 4049
In stock, ready to ship!

$215.75

+
Bending Iron Mandolin/Violin Side Bending Extension

Mandolin/Violin Side Bending Extension

Item # 0688
In stock, ready to ship!

$10.45

+
Currency:
Total: $0.00
Quantity: 20

Product Details

Variable temperature and versatile bending radii. Here's a well-made iron that's ideal for bending wet or steamed sidewood in the small shop.

Crafted from 6-1/4" long cast aluminum, it features variable temperature control and a versatile shape allowing a wide variety of bending radii.

Tip: Bending wood successfully requires practice, and we recommend using stainless steel Side Bending Straps to support wood sides during bending. We offer inexpensive practice wood and free instructions to help you get started.

The Bending Iron's highest temperature is approximately 500° (good bending temperature is between 350° and 400°). A surface thermometer placed on the aluminum iron is the best way to monitor the temperature.

To bend the tight curved sides of a mandolin or violin, screw on our unique #0688 Mandolin/Violin Side Bending Extension.

The sturdy wooden base can be clamped to your workbench horizontally or vertically.

#0689 Domestic model is a 120-volt (200 watt) AC electrical appliance. It has a U.S. standard Type B plug with two flat parallel prongs and a grounding pin.

#4049 International model is a 220-volt (200 watt) AC electrical appliance has international plug CEE 7/7 (compatible with Type E and F receptacles) with two round prongs and two grounding clips on the sides and female contact to accept the grounding pin.


Product Instructions

Bending Sides With a Bending Iron

An introduction to bending wood using a Bending Iron.

Ratings & Reviews

Bending Iron

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
  • Based on 27 Reviews
Displaying 1 of 3 1 2 3
Write a review

Nice heating iron but slow to warm up

By Shawn H. from Kentucky, USA
(Customer's Reviews) Wednesday, April 23, 2014


The heating iron is really nice itself. To me it seems sturdy and well built. I would have given it 5 stars if it didn't take almost an hour for it to reach 300 degrees F.

It dose the job

By JSD from Europe
(Customer's Reviews) Monday, March 24, 2014


This works well, though mine wobbles a bit and as some of the other reviews say it dose have a cheapish vibe... It still works and you can bend sides but a hot pipe is much better and sturdier.

Bending Iron

By justinarts from West Texas, USA
(Customer's Reviews) Monday, January 20, 2014


It is a fine bending iron. I also bought the extension for violin ribs and it worked as described. I used a homemade one for years. This one is a little slower to heat up but I just plan ahead and no problem.

Good and not too expensive iron with side bending extension

By Anders from Norway
(Customer's Reviews) Thursday, August 08, 2013


But a little too big just for violin making. But probably ideal for guitar builders.

Low quality tool.

By Nate Clark from Ithaca, NY
(Customer's Reviews) Thursday, December 06, 2012


The Ibex bending iron works fine but has a general cheap feel and is slow to heat up. Most notably, the violin/mandolin bending extension didn't fit the threads that are tapped into the main iron. The extension is the only reason I chose to buy this bending iron from Stewmac. I brought this to Stewmac's attention and their solution was to force the screw so that it would cut new threads into the aluminum bending iron. In order to do this I had to first file the opening of the boss in the aluminum so it would accept the long, unthreaded section at the tip of the machine screw. Once the threads hit the aluminum they chewed up the old threads without too much force. With the machine-screw snug, the connection between the main iron and the extension is solid. This aspect of the tool seems a bit cheap to me and I am suspect of the long term integrity of the threads. Two stars because a specialty tool should not require modification to be used as designed.

Again the best service

By Herman Arendsen Guitars from the Netherlands
(Customer's Reviews) Friday, November 30, 2012


I had this iron for some years. It turned out to be a fantastic tool. But now the iron did not get hot enough anymore and I asked customer service for a replacement heating element. This was not available and without asking they offered to send me a completely new iron for free! Where do you find such a service? I'm happy, thank you very much.

Service beyond service

By John L from Kalamazoo, MI
(Customer's Reviews) Tuesday, November 20, 2012


I bought the bending iron in 2003 for the purpose of pre-bending those few pieces of wood that won't bend evenly when used for a rosette.

Last weekend I finally hit a piece of rosewood that was too stiff in the middle to bend like the rest and thought "finally, I can try this thing out." Well, it didn't work and I had never tested it.

So I wrote customer service, asking which part they thought needed replacing, given the results of my electrical testing. I was hoping they could direct me to a source too.

On Monday I got an email saying a new one plus a pre-paid shipping label to send the defective one back was on its way.

You can trust Stew Mac to not only treat you right, but treat you well. I was certainly treated better than I deserved. Nine years is a long time to let something sit without testing and the thought they would still stand behind it like I bought it yesterday is amazing.

Cutaways

By GavinB from Perth, Australia
(Customer's Reviews) Thursday, October 11, 2012


I use the 220 volt bending iron for my rosette bindings and for brnding the wood to insert in the cutaway channel. I dont use it for bending sides as i prefer the templated option. Wood thickness is very important to effect a good quality bend. I wrap my wood in a wet piece of thin sheeting cover both with tin foil. I get a mineral free clean smooth finish.

Bending Iron

By Bernd Krause from Maine, NY
(Customer's Reviews) Tuesday, September 04, 2012


I have been using this bending iron for over 20 years now and it has never let me down. I can't understand some of the comments that say it doesn't get hot enough. I bend mostly dulcimer sides out of quartersawn air dried walnut and spray with water as needed. It bends beautifully at a temperature setting a little over 4, which is approximately 260-280 degrees. For woods like curly koa, rosewood, curly maple, etc., I have better results soaking in hot water for about 10 minutes and they bend just fine with occasionally spraying with a little water as needed, at just a little higher temperature setting. Most of these woods are kiln dried which tend to make them brittle and need soaking. My dulcimers also have solid linings made of basswood, which I freehand bend at the same temperature, only spraying with water. Yes, the bender takes a little time to heat up; but I find the heat is constant and the iron holds it well. It's not suppose to bend a side instantly. I've had good luck with sides for guitar and mandolin as well. My bender is an older version and the only thing I wish it had was the attachment for small bends. Other than that, I only wish I had purchased it 34 years ago when I began building. Best investment in a luthier tool I ever made.

A needed product

By Beau Hannam Guitars from Grand Junction, CO 
(Customer's Reviews) Thursday, July 26, 2012


You need this product for touch up bending work etc. Could be a little larger but works well enough at this size.

Displaying 1 of 3
1 2 3


Shown on page 76 of our latest catalog.