Trade Secrets!

Removing the glued-in saddle on a 1937 Martin D-28 Herringbone


Issue 68 August 21, 2008

Photo: string windings on saddle Dan Erlewine on Acoustic Repairs

These string windings
aren’t supposed to be up here on the saddle!
This 1937 Martin saddle is way too low. And it’s glued in tight, so replacing it is going to be tricky...

Dan Erlewine signature Dan Erlewine, August 21, 2008
Dan Erlewine
This bridge saddle is so low that the string windings are riding right up onto it. They’ll chew up the saddle and cause poor intonation.

Somebody shaved this saddle down to lower the action. The proper fix would have been to leave the saddle alone and instead remove the neck and reset it at a steeper angle that works with the original saddle height. That’s my plan for this Martin D-28, but for now let’s focus on removing and replacing the saddle.

Photo: saddle is too low
This saddle is fastened with hide glue. Glued-in saddles are difficult enough to remove even when you can get a good grip on them with fret pullers, but this one was extra trouble because its rounded top was barely peeking over the top of the bridge. There’s nothing to grab onto!

Photo: filing the saddle flat
Here's how I got it out:

I started by using a coarse fingerboard leveler to flatten the top of the saddle.

Fingerboard Leveling File
Fingerboard Leveling File
Photo: drill through the saddle
This allowed me to drill small holes right down through the top of the saddle — stopping when the drill bit had passed through the bone and hit the ebony in the bottom of the saddle slot.

These holes serve
three purposes:


Vintage Bone Saddles
Vintage Bone Saddles
Photo: add water
1. Using a pipette, I dripped small amounts of hot water into the holes to soften the hide glue below.

Pipettes
Pipettes
Photo: add heat
2. The holes also provide a place for a pointed-tip soldering iron to center on as I apply heat across the saddle. This steams the glue loose under and around the saddle.
Photo: pry the saddle out
3. I pry the saddle upward with a small micro-chisel, its width thinned on a belt sander so it’s slightly narrower than the walls of the saddle slot. The saddle breaks at each hole — making it unnecessary to pry out the entire saddle at once. It pops out, a piece at a time.

Micro Chisels
Micro Chisels
BridgeSaver tool
When string windings are pulling up onto the saddle, another possible trouble is a worn bridge pad. Over the years the ball ends of the strings can chew into the wood under the bridge, moving ever upward. This used to mean replacing the bridge pad, but now there’s a better solution: the BridgeSaver cleanly installs a plug of new wood under each bridge pin, leaving the original pad in place!

BridgeSaver in use
Photo: sanding station

Photo: press-fit saddle
Making the replacement saddle:

Over the years I’ve become adept at thicknessing saddles by hand on a belt sander, but these days I prefer the accuracy of the Luthier's Friend Sanding Station. A strip of wood holds the bone saddle up toward the middle of the sanding drum while I push the saddle blank through.

The new saddle is a perfect press fit.

I trace the shape of the bridge top onto the bone, then draw my saddle height using a 20" radius gauge. This is the line I’ll follow to shape the saddle on my belt sander.

Luthier’s Friend Sanding Station
Luthier’s Friend Sanding Station





Radius Gauges
Radius Gauges
Photo: marked-up saddle
Photo: ready for final shaping

Ready for final shaping and polishing!

Acoustic Bridges
Acoustic Bridges

Dan Erlewine signature

Problem-solving products mentioned above:
Photo: 3-Piece Inspection Mirror Photo: Luthier's Friend Sanding Station Photo: Radius Gauges
3-Piece Inspection Mirror
See the big picture of the guitar's interior! Thin folded mirrors to insert easily into the guitar, then unfolded once inside the guitar.
Luthier's Friend Sanding Station
The versatile Luthier's Friend Sanding Station works with your shop drill press. It lets you thickness-sand small parts quickly and accurately. Pattern-sand with your own templates, too.
Radius Gauges
Notched design reads the fretboard with the strings on! Make sure you keep the right curvature when working on a fingerboard.
Buy Now
Buy Now
Buy Now
Photo: Micro Chisels Photo: Fingerboard Leveling File Photo: Pipettes
Micro Chisels
Set of four model maker's chisels, for trimming nut and saddle slots or for removing dried glue around braces and frets.
Fingerboard Leveling File
A special "double-cut" file that quickly removes and levels fingerboards and inlays.
Pipettes
Useful in every shop when gluing, finishing, more!
Buy Now
Buy Now
Buy Now

Don't miss an issue!

Get Trade Secrets delivered to your inbox. Only from StewMac.