Trade Secrets!

Make this brad-point bit for installing side dots

Issue 8 December 14, 2006

Photo: Dan Erlewine I modified this drill bit to install fingerboard dots that line up on center

Drilling holes for side dots on a fretboard isn’t easy with ordinary twist drills because twist drills seem to enjoy wandering off center!
I can’t deliver a customer’s guitar with the dots staggering around the edge of the fingerboard, so I solved this problem in my shop by grinding a tiny brad point onto a 3/32" twist bit. Here’s how to do it.

Dan Erlewine signature Dan Erlewine, December 14, 2006
Photo: brad point drill bit
Making my own brad-point bit
Photo: anvil depth micrometer

I found this nifty anvil-base depth micrometer in a box of tools, and used it for years to measure fret height. My repairman pal Frank Ford offered a better solution, and Don MacRostie made it happen: a luthier-friendly caliper that straddles the fret and gives a digital readout.

Photo: Luthier's Caliper

Photo: Luthier's Caliper

The modified jaw fits over the fret tang to measure fretwire crown height, too. This custom caliper is the one we now carry at

Photo: drill bits compared
Here's an enlargement of my homemade brad point bit vs. the standard twist drill it was before I modified it. You can see how the brad point is going to stay on center, creating a nice flat-bottomed hole.
Photo: grinder setup 1
Step 1
Put a small grinding wheel into your Dremel tool, and mount it in the precision router base. Clamp this into a small vise. I'm using my nut and saddle vise — it's a heavy little thing, and it makes a good "third hand" with a solid grip.
Photo: grinder setup 2
Clamp that rig to your benchtop and you have a small Dremel "grinder" with a working table.
Photo: grinder fence
Step 2
Clamp a small square item to the router base to use as a fence, centering it with the router bit. The drill bit will ride against this fence. (I used the square corner of our steel Fret Rocker for this.)

The blue marker ink on the drill bit will make it easy to see where the grinder's removing metal.
Photo: repair magnet

This turned out to be a handy trick: I clamped a 1" repair magnet to the underside of the aluminum router table — the force of the magnet keeps the drill bit hugging the table and fence.

Photo: brad point bit closeup
Step 3
Grind each cutting edge flat, stopping before reaching the center — leave that brad point!
Photo: finishing brad point bit
On the face of the wheel, grind a little back angle leading up to the cutting edge of the lip. Dress the new edges by hand with a sharp file (I used my diamond nut file).
Photo: installing side dot
The sharpened tip will keep the bit centered, and the new bit will drill a clean, sharp-edged hole.

Just the right size for a white side dot.
Photo: how to measure a drill
How not to measure a drill bit

Did you know the way to measure a drill’s diameter is not by putting a caliper on the shank? (I learned this from hanging around machinist-types.) Instead, measure the cutting tip from point to point; that’s what makes the hole, and it’ll be wider than the shank.

Problem-solving products mentioned above:
Photo: Nut and Saddle Vise Photo: Precision Router Base Photo: Dremel 4000 Rotary Tool Outfit
Nut and Saddle Vise
We designed this special vise that gives you the clearance needed for easier, more efficient work.
Precision Router Base
Adjusts precisely and holds your Dremel tool without wobbling!
Dremel 4000 Rotary Tool Outfit
Versatile high performance rotary tool for precision small-scale inlaying, polishing, grinding, routing and more.
Buy Now
Buy Now
Buy Now
Photo: Guitar Repair Magnets Photo: Luthier's Digital Caliper Photo: Plastic Side Dot Materials
Guitar Repair Magnets
These seriously strong, neodymium boride magnets have hundreds of repair and building uses around the shop.
Luthier's Digital Caliper
Our precision digital caliper has a custom notches for measuring fretwire crown height (the height above the fretboard) before and after the fretwire has been installed or removed.
Plastic Side Dot Materials
White and black plastic side dot materials.
Buy Now
Buy Now
Buy Now

Don't miss an issue!

Get Trade Secrets delivered to your inbox. Only from StewMac.