Pickguard Adhesive Sheet

  • 25 Reviews
  • Write a review

No brushing, no mess, no cleanup. Here's the easy way to attach an acoustic guitar pickguard.

Read more

Pickguard Adhesive Sheet

Item # 4597
In stock, ready to ship!

$3.35

6 or more $2.91
12 or more $2.51
+
Quantity Discount Prices apply when you buy multiples of the same item number.
Currency:
Total: $0.00
Quantity: 20

Product Details

No brushing, no mess, no cleanup. Here's the easy way to attach an acoustic guitar pickguard.

Strong 3M® pure adhesive in a conveniently-sized sheet with protective covering on each side. The sheet is .002" x 6" x 8" (0.05mm x 152.40mm x 203.20mm), for use on finished surfaces only.

Attach a pickguard with no mess and no cleanup:
1. Peel away the blue covering
2. Adhere the sheet to the back of the pickguard
3. Carefully trim away the excess
4. Peel away the remaining covering
5. Attach the pickguard to the guitar


Ratings & Reviews

Pickguard Adhesive Sheet

  • EXCELLENT PRODUCT
  • GOOD PRODUCT
  • AVERAGE PRODUCT
  • FAIR PRODUCT
  • POOR PRODUCT
  • Based on 25 Reviews
Displaying 2 of 3 1 2 3
Write a review

Flatten warped pickguards

By GuitarzanMoore from Columbiana, Ohio
(Customer's Reviews) Thursday, November 01, 2012


Excellent product. Particularly if you run across a a warped pickguard on a vintage guitar. I have a vintage Ventura lawsuit hummingbird 12 string whose pg was domed out. I carefully removed it and cleaned the back and carefully cleaned and resealed the area on the guitar with nitro lacquer. Solvents can be used but never on the face of the pickguard! (lacquer thinner/naptha etc. spot check first!) Then I placed the pickguard in boiled hot water until it softened enough to re-flatten. Then pressed it between 2 pieces of wood and weighted it till cooled. Then applied the adhesive sheet peeling back a starting edge and then continuing to apply while securing as I peeled the cover sheet and then trimmed to shape. Then removed the other cover and placed the pickguard in place and pressed down to remove any remaining convex shape or doming. I weighted it down for a while just for my own security, I doubt this was needed. The finished job was as good as new. Lots of other uses too.

Pretty good stuff.

By CWaggs from Illinois
(Customer's Reviews) Thursday, October 25, 2012


There are no instructions. 1st time users: read some more of these reviews for pointers on avoiding bubbles & wrinkles. Getting a great result without these helpful tips would've been difficult. Thanks to the great StewMac reviewers for the thoughtful pointers!

Highly Recommended

By Peter haynes from Bermuda
(Customer's Reviews) Wednesday, October 10, 2012


The pickguard was easy to trim and easy to apply and sticks like glue,
Excellent.

Highly suggested!

By jojokeo from Huntington Beach CA
(Customer's Reviews) Saturday, October 06, 2012


Using this for my Strats has made a definite improvement on background noise. Guitars are almost dead silent with it. Notice a few little pieces on pickguard & guitar top helping to create a positive connection between the two. This creates one large completely shielded compartment & don't forget to use shieded wiring from volume pot to output jack (I hadn't done this step yet in pic).

good sticky stuff

By Bill's repair from Madisonville,TN.
(Customer's Reviews) Wednesday, December 28, 2011


This stuff is awsome. After shaping my tortoloid pickguard, I placed it on the adhesive sheet & cut it to match the pickguard. I placed it on the guitar and it looks awsome. This stuff really holds. Thanks Stew Mac

More than one purpose.

By TommyGuitars from Osaka, Japan
(Customer's Reviews) Sunday, November 06, 2011


These have been helpful in more than just it's recommended application. For example holding parts in place in order to align drilling templates and etc. Also, good for putting up posters around the shop's walls.

FANtastic

By Tim B from NC
(Customer's Reviews) Friday, September 23, 2011


I don't use anything else anymore for fastening pickguards. I use the left over pieces for attaching wood, etc. to jigs, clamps and alike. Just be sure to reduce the tackiness on your pants or shirt first or you'll have trouble getting it off.

Big help

By thefrankie from Nashville,TN
(Customer's Reviews) Friday, September 09, 2011


My luthier here in Nashville used this to put a pick guard on one of my Recording Kings. Did the job perfectly.

bon produit

By chaladichal from france
(Customer's Reviews) Monday, June 20, 2011


posT sur ma guitare, sans probleme !

Go slow

By Julyan Wallis, Guitar Doctor UK from Cornwall, UK
(Customer's Reviews) Wednesday, May 04, 2011


Excellent quality to do the job right.

Displaying 2 of 3
1 2 3


Shown on page 37 of our latest catalog.